What to do if PROLiNK MASTER II UPS displays error codes 14, 15, 16, 17, 18, or 19?
If your PROLiNK UPS shows error codes 14, 15, 16, 17, 18, or 19, this indicates a short circuit in the UPS output, causing it to shut off automatically. You should check the output cable and the connected device for any short circuit issues.
Why does my PROLiNK MASTER II UPS show warning code 09?
Warning code 09 on your PROLiNK UPS means it's overloaded. This can occur if the devices connected to the UPS are fed directly by the electrical network via the Bypass, or after repetitive overloads, the UPS is locked in the Bypass mode. To resolve this, remove excess loads from the UPS output. If the UPS is locked in Bypass mode, remove the excess loads first, then shut down the UPS and restart it.
What to do if PROLiNK MASTER II shows fault code 43?
If your PROLiNK UPS displays fault code 43, it means the UPS was overloaded for too long, resulting in a fault and automatic shutdown. To fix this, remove excess loads from the UPS output and then restart it.
Why is my PROLiNK MASTER II UPS showing warning code 01?
Warning code 01 on your PROLiNK UPS indicates that the external or internal battery is incorrectly connected. You should check if all batteries are connected properly.
What does warning code 0A mean on PROLiNK MASTER II UPS?
Warning code 0A on your PROLiNK UPS means that the fan is locked or malfunctioning, or the UPS temperature is too high. Check the fan.
What to do if the icons and warning code flash and alarm sounds every second on my PROLiNK Battery Pack?
If the PROLiNK Battery Pack is overloaded, remove some of the connected devices from the UPS output. This issue might also occur if devices are powered directly by the mains due to an overload. After repeated overloads, the UPS might lock in Bypass mode. To resolve this, first remove excess loads, then shut down and restart the UPS.
Why is the PROLiNK MASTER II battery backup time so short?
A shorter than expected battery backup time in your PROLiNK UPS could be due to a couple of reasons. First, the batteries may not be fully charged. Charge the batteries for at least 5 hours and then check capacity. Another possibility is that the batteries are defective.
Why is the PROLiNK MASTER II UPS beeping every 2 seconds?
If the icon and a warning code are flashing on the LCD display and the alarm is sounding every 2 seconds, it could be due to several reasons: * The EPO function is activated. Set the circuit in closed position to disable EPO function. * Line and neutral conductors of the UPS input are reversed. Rotate the mains power socket by 180° and then connect to the UPS system. * The external or internal battery is incorrectly connected. Check if all batteries are connected well.
Why is my PROLiNK MASTER II battery backup time so short?
A shorter than expected battery backup time on your PROLiNK UPS can be due to a battery that isn't fully charged. Charge the battery for at least 7 hours to ensure it reaches full capacity. If the problem continues after a full charge, it may indicate a battery defect.
What to do if PROLiNK MASTER II error code 43 is displayed?
If your PROLiNK UPS displays error code 43, it indicates that the UPS was overloaded for too long and became damaged, causing it to shut down automatically. To resolve this, remove some of the devices connected to the UPS to reduce the load, and then turn the UPS back on.
General| Waveform | Simulated Sine Wave |
|---|---|
| Type | Line Interactive |
| Input Frequency | 50 or 60Hz |
| Output Frequency | 50/60Hz |
| Typical Recharge Time | 4-6 hours |
| Protection | Overload Protection |
| Outlets | Universal Socket x 3 |
| Audible Alarm | Low Battery, Overload, Fault |
To Next Page
