What to do if PROLiNK MASTER II UPS displays error codes 14, 15, 16, 17, 18, or 19?
If your PROLiNK UPS shows error codes 14, 15, 16, 17, 18, or 19, this indicates a short circuit in the UPS output, causing it to shut off automatically. You should check the output cable and the connected device for any short circuit issues.
Why does my PROLiNK MASTER II UPS show warning code 09?
Warning code 09 on your PROLiNK UPS means it's overloaded. This can occur if the devices connected to the UPS are fed directly by the electrical network via the Bypass, or after repetitive overloads, the UPS is locked in the Bypass mode. To resolve this, remove excess loads from the UPS output. If the UPS is locked in Bypass mode, remove the excess loads first, then shut down the UPS and restart it.
What to do if PROLiNK MASTER II shows fault code 43?
If your PROLiNK UPS displays fault code 43, it means the UPS was overloaded for too long, resulting in a fault and automatic shutdown. To fix this, remove excess loads from the UPS output and then restart it.
What does fault code 28 mean on my PROLiNK Battery Pack?
If fault code 28 is displayed on the LCD and the alarm is continuously sounding on your PROLiNK Battery Pack, it indicates that the battery voltage is too low or the charger is faulty. Contact your dealer.
What does warning code 0A mean on PROLiNK MASTER II UPS?
Warning code 0A on your PROLiNK UPS means that the fan is locked or malfunctioning, or the UPS temperature is too high. Check the fan.
What to do if fault code 43 is shown on PROLiNK Battery Pack?
If fault code 43 and the icon are displayed on the LCD and the alarm is sounding continuously on your PROLiNK Battery Pack, it means the UPS shut down automatically due to an overload at the output. To fix this, remove excess loads from the UPS output and then restart the UPS.
Why is the PROLiNK MASTER II battery backup time so short?
A shorter than expected battery backup time in your PROLiNK UPS could be due to a couple of reasons. First, the batteries may not be fully charged. Charge the batteries for at least 5 hours and then check capacity. Another possibility is that the batteries are defective.
Why is the PROLiNK MASTER II UPS beeping every 2 seconds?
If the icon and a warning code are flashing on the LCD display and the alarm is sounding every 2 seconds, it could be due to several reasons: * The EPO function is activated. Set the circuit in closed position to disable EPO function. * Line and neutral conductors of the UPS input are reversed. Rotate the mains power socket by 180° and then connect to the UPS system. * The external or internal battery is incorrectly connected. Check if all batteries are connected well.
What does fault code 45 mean on my PROLiNK Battery Pack?
If fault code 45 is displayed on the LCD and the alarm is continuously sounding on your PROLiNK Battery Pack, it means the charger does not have an output and the battery voltage is less than 10V/PC. Contact your dealer.
What to do if PROLiNK MASTER II error code 43 is displayed?
If your PROLiNK UPS displays error code 43, it indicates that the UPS was overloaded for too long and became damaged, causing it to shut down automatically. To resolve this, remove some of the devices connected to the UPS to reduce the load, and then turn the UPS back on.
Guidelines for safely transporting and storing the UPS system.
Pre-installation checks and environmental considerations for the UPS.
Instructions for safely installing the UPS unit.
Critical safety warnings and advice for connecting the UPS.
Basic guidelines for operating the UPS system safely.
Overview of safety and EMC standards the UPS complies with.
Procedure for unpacking and inspecting the UPS unit upon arrival.
Diagrams and descriptions of the UPS wiring terminal connections.
Step-by-step guide for installing a single UPS unit.
Instructions for installing UPS units in a parallel configuration.
Guide to installing the UPS monitoring software.
Explanation of the UPS control panel buttons and their functions.
Overview and explanation of the UPS LCD screen menus and functions.
Details on UPS audible alarms, their meanings, and muting options.
Step-by-step guide for operating a single UPS unit.
Procedures for setting up and operating UPS units in parallel.
List and explanation of UPS fault codes for troubleshooting.
List and explanation of UPS warning codes for status monitoring.
Recommendations for proper storage of the UPS unit.
Guidelines for performing routine maintenance on the UPS system.
Detailed technical specifications for the UPS models.
General| Waveform | Simulated Sine Wave |
|---|---|
| Type | Line Interactive |
| Input Frequency | 50 or 60Hz |
| Output Frequency | 50/60Hz |
| Typical Recharge Time | 4-6 hours |
| Protection | Overload Protection |
| Outlets | Universal Socket x 3 |
| Audible Alarm | Low Battery, Overload, Fault |
To Next Page
