How to fix a Protemp PT-16-TTC that will not light?
If your Protemp Heater won't light, here are a few things to check: * Make sure the valve on the propane cylinder is open by turning it counterclockwise. * Ensure the propane cylinder is not empty and refill if necessary. * Verify the regulator is in the (HI) position. * If none of these steps work, the regulator may be defective and need replacement.
What to do if the Protemp PT-16-TTC burner won't stay lit?
If the burner on your Protemp Heater won't stay lit after releasing the gas valve plunger, consider these possible causes: 1. The tip switch might be activated or defective. Ensure the heater is upright, or replace the tip switch. 2. Check all wiring connections to ensure they are properly connected. 3. The thermocouple may be defective and require replacement. 4. A defective MPU may also be the cause, requiring replacement.
What to do if my Protemp PT-16-TTC will not light?
If your Protemp Heater won't light, there are several potential causes: * The valve on the propane cylinder might be closed. Open the cylinder valve by turning it counterclockwise. * The propane cylinder could be empty. Refill the cylinder. * The regulator might not be in the (HI) position. Turn the regulator to the (HI) position. * The regulator could be defective. Replace the regulator assembly.
Why are there excessive flames coming out of my Protemp Heater burner?
If you observe excessive flames coming out of the burner of your Protemp Heater (not glowing red) or flames flashback/burn inside the mixing tube, it could be due to: * Blocked or covered air inlet holes. Clear any obstructions. * A damaged burner screen. Replace the burner screen. * A gap between the burner screen and burner can. Replace or repair the burner head assembly.
How to fix excessive flames on Protemp PT-16-TTC?
If you're experiencing excessive flames coming out of the burner of your Protemp Heater (not glowing red) or flames flashback/burning inside the mixing tube, consider the following: * Air inlet holes might be blocked or covered. Clear any obstructions. * The burner screen could be damaged. Replace the burner screen. * There might be a gap between the burner screen and burner can. Replace or repair the burner head assembly.
What to do if pilot light is too long on Protemp PT-16-TTC?
If the pilot light on your Protemp Heater is too long and the burner won't stay lit, it may be due to low oxygen in the space. Ventilate the area to bring in fresh air.
Why are there excessive flames coming out of my Protemp PT-16-TTC?
If you're experiencing excessive flames coming out of the burner of your Protemp Heater, and they're not glowing red, or if flames are flashing back/burning inside the mixing tube, here's what you should do. Start by checking the air inlet holes to ensure they aren't blocked or covered; clear any obstructions. If the issue continues, inspect the burner screen for damage and replace it if needed. Finally, check for a gap between the burner screen and burner can; if a gap exists, replace or repair the burner head assembly.
Why burner will not stay lit on my Protemp Heater when gas valve plunger is released?
If the burner on your Protemp Heater won't stay lit when the gas valve plunger is released, it could be due to: 1. The tip switch being activated or defective. Ensure the heater is in an upright position, or replace the tip switch. 2. Unplugged wire terminal connections. Check all wiring connections. 3. A defective thermocouple. Replace the thermocouple. 4. A defective MPU. Replace the MPU.
Details critical safety warnings about death, injury, and property damage from fire, explosion, and other hazards.
Warns about keeping combustibles away from the heater and avoiding volatile environments.
Lists restrictions on use in RVs, enclosed spaces, and residential areas, and general safe practices.
Specifies conditions for indoor use, limited to temporary heating in adequately ventilated structures.
Emphasizes reading and understanding instructions to prevent severe hazards like death or injury.
Notes the heater is unvented and requires adequate combustion and ventilation air for safety.
Alerts about lead and chemicals known to cause birth defects or reproductive harm.
Covers indoor air pollution, carbon monoxide poisoning, propane explosion risks, and burn/fire hazards.
Provides critical instructions on what to do if the smell of gas is present.
Details minimum clearances from combustibles and hot surfaces for safe operation.
Covers safe use with propane, cylinder size limits, and protection for the hose assembly.
Mandates upright vertical position and stable, level surface for the heater.
Lists BTU, fuel consumption, operating hours, cylinder size, and heating area for different models.
Illustrates key components of the PT-16-TTC model with labels.
Illustrates key components of the PT-32-TTC model with labels.
Illustrates key components of the PT-47-TTC model with labels.
Visual representation of heater parts with numerical labels for identification.
Table listing replacement parts with their corresponding item numbers and model identifiers.
Step-by-step guide for assembling the heater, including model-specific details.
Instructions for setting burner face direction using the plane washer on the tank collar bracket.
Details on safely connecting the heater to an LP cylinder for operation.
Information on using propane, its properties, and required cylinder equipment.
Cautions on handling LP cylinders, tipping, storage, and avoiding excessive heat.
Step-by-step guide to safely light the heater burners, including safety precautions.
Specifies minimum ventilation openings needed for safe operation based on BTU output.
Procedures for safely shutting down, cooling, and disconnecting the heater.
Guidelines for inspecting, maintaining, and storing the heater and LP cylinder.
Instructions on how to find the heater's serial number for customer support.
Table detailing common issues like unit not lighting or burner not staying lit, with possible causes and solutions.
Details the warranty period, coverage, exclusions, and responsibilities of the purchaser.
Instructions on how to make a warranty claim, including specifying model and serial numbers.
To Next Page
General