EasyManua.ls Logo

Protemp PT-45-KF - User Manual

Protemp PT-45-KF
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Model Numbers
PT- 45-KFA / PT-70T-KFA / PT-75T-KFA / PT-125T-KFA / PT-175T-KFA / PT-215T-KFA
© 2015 Pinnacle Products International, Inc.
668 Stony Hill Road #302 Yardley, PA 19067 USA • Toll Free (800)-641-6996
Fax: (215)-891-8461 • Web: www.protemp.us • Email: info@pinnacleint.com
User’s Manual &
Operating Instructions
CONSUMER: READ AND SAVE THESE INSTRUCTIONS
701000129-15
GENERAL HAZARD WARNING:
READ AND UNDERSTAND ALL OF THE INSTRUCTIONS IN THIS MANUAL
BEFORE ASSEMBLING, STARTING, OR SERVICING THE HEATER. Be sure to comply with the
instructions and warnings provided with this heater. Failure to comply can result in fire or explosion
that can cause property loss, bodily injury, or loss of life. Only persons who can follow and
understand these instructions should operate or service this heater. If you need heater info; such as
an operating manual, labels, etcetera, contact Pinnacle Products International at 800-641-6996.
DANGER
NOT FOR USE IN RESIDENTIAL LIVING AREAS OR IN ENCLOSED SPACES
WITHOUT ADEQUATE VENTILATION. FOR OUTDOOR USE. INDOOR USE
PERMITTED ONLY FOR: THE TEMPORARY HEATING OF ADEQUATELY VENTILATED
BUILDINGS OR STRUCTURES UNDER CONSTRUCTION, ALTERATION OR REPAIR. This is
an unvented portable heater that uses air (Oxygen) from within the area in which it is used. Failure
to provide adequate combustion and ventilation air will result in asphyxiation, carbon monoxide
poisoning, bodily injury or death. Refer to “Ventilation” on Page 7.
DANGER
®
FACTORY ID: 001

Table of Contents

Questions and Answers

  • D
    Dr. Brenda ScottAug 19, 2025
    Why Protemp Heater has poor combustion and excess soot production?
    • K
      kayla28Sep 12, 2025
      Poor combustion and excess soot production in your Protemp Heater may be due to: * Dirty input, output, or lint filter: Clean or replace the air or lint filter. * Dirty fuel filter: Clean or replace the fuel filter. * Poor quality of fuel: Flush the fuel tank and refuel the heater with good quality fuel. * Incorrect PSI: Ensure you are using the proper pressure. * Dirty nozzle: Clean or replace the nozzle.
  • N
    Nancy MartinAug 25, 2025
    What to do if my Protemp PT-45-KF Heater will not operate and shows error E1?
    • H
      hayesallisonAug 25, 2025
      If your Protemp Heater won't operate, the motor runs briefly, and the LED displays “E1”, consider these potential causes: * No kerosene in the fuel tank: Fill the tank with fresh kerosene. * Incorrect pump pressure: Adjust the pump pressure. * Corroded spark plug or incorrect plug gap: Clean or replace the spark plug. * Dirty fuel filter: Clean or replace the fuel filter. * Dirty nozzle: Clean or replace the nozzle. * Moisture in fuel tank: Rinse the fuel tank with clean, fresh kerosene. * Improper electrical connection between transformer and circuit board: Inspect all electrical connections. * Ignitor wire not connected to spark plug: Re-attach the ignitor wire to the spark plug. * Defective ignitor: Replace the ignitor. * Improper spacing with rotor: Adjust rotor.
  • K
    kingjoseAug 26, 2025
    What to do if my Protemp PT-45-KF fan does not operate and shows error E1 or E2?
    • A
      Alexander HowardAug 26, 2025
      If the fan in your Protemp Heater does not operate when plugged in and the power switch is in the “ON” position, and the LED display shows “E1” or “E2”, check the following: * Thermostat setting: Rotate the thermostat to a higher setting. * Electrical connections: Inspect all electrical connections between the main PCB and the motor.
  • S
    Sarah ClarkAug 28, 2025
    What to do if my Protemp Heater does not turn on?
    • M
      Maria JimenezAug 28, 2025
      If your Protemp Heater does not turn on and the lamp is not lit, consider the following: * Temperature limit sensor: Push the power switch to “OFF” and allow the heater to cool for 10 minutes, then restart the heater. * Electrical power: Check the power cords for proper connection and test the power supply. * Fuse: Check or replace the fuse. * Improper electrical connection: Inspect all electrical connections between the temperature limit sensor and the circuit board.
  • L
    lori49Aug 30, 2025
    What to do if Protemp Heater doesn't operate and shows E1?
    • J
      Jorge GrayAug 30, 2025
      If your Protemp Heater doesn't operate, the motor runs briefly, the lamp flickers, and the LED displays 'E1', here are some things to check: 1. Ensure the fuel tank has fresh kerosene. 2. Adjust the pump pressure if it's incorrect. 3. Clean or replace a corroded spark plug with an incorrect gap. 4. Clean or replace the fuel filter if it is dirty. 5. Clean or replace the nozzle if it is dirty. 6. Rinse the fuel tank with fresh, clean kerosene if there's moisture inside. 7. Inspect all electrical connections between the transformer and circuit board. 8. Re-attach the ignitor wire to the spark plug if it's disconnected. 9. Replace the ignitor if it is defective.
  • L
    Luis JohnsonSep 1, 2025
    Why does my Protemp PT-45-KF shut off after igniting and shows E1?
    • M
      Mark BrownSep 2, 2025
      If your Protemp Heater ignites but the main PCB shuts off shortly after, displaying 'E1' and the lamp flickers, it could be due to several reasons: * Incorrect pump pressure, which requires adjustment. * A dirty input, output, or lint filter, which should be cleaned or replaced. * A dirty fuel filter, which should be cleaned or replaced. * A dirty nozzle, which should be cleaned or replaced. * A dirty photocell lens, which should be cleaned or replaced. * Improper installation or a defect in the photocell, requiring adjustment, or replacement. * Improper electrical connection between the main PCB and photocell; check wiring connections.
  • K
    Karla CordovaSep 4, 2025
    Why does my Protemp PT-45-KF Heater shut off after a short time and show error code E1?
    • A
      Angela HartSep 4, 2025
      If your Protemp Heater ignites but the main PCB shuts off shortly after, and the LED display shows “E1”, here are some possible solutions: * Adjust the pump pressure. * Clean or replace the air, lint, or fuel filter. * Clean or replace the nozzle and photocell. * Adjust the photocell position or replace it if defective. * Check the wiring connections between the main PCB and photocell, and the placement of the thermister sensor. * Replace the temperature limit switch.
  • S
    Savannah BartonSep 6, 2025
    What to do if my Protemp PT-45-KF Heater will not operate and shows error code E1?
    • C
      Cole HammondSep 6, 2025
      If your Protemp Heater won't operate, or the motor runs briefly and the LED display shows “E1”, the following steps may help: 1. Refill the tank with fresh kerosene. 2. Adjust the pump pressure. 3. Clean or replace the spark plug, fuel filter, and nozzle. 4. Rinse the fuel tank with clean kerosene. 5. Inspect electrical connections. 6. Re-attach the ignitor wire to the spark plug, replace the ignitor if necessary, and adjust the rotor.
  • S
    Sara RuizSep 8, 2025
    How to fix poor combustion and soot production in Protemp PT-45-KF Heater?
    • J
      John BrandtSep 8, 2025
      If your Protemp Heater produces poor combustion or excess soot, consider these solutions: * Clean or replace the air, lint, and fuel filters. * Flush the fuel tank and refuel the heater with good quality fuel. * Ensure you are using the proper pressure. * Clean or replace the nozzle.
  • S
    Steven RodriguezSep 12, 2025
    Why is the fan not working on my Protemp Heater and showing E1 or E2?
    • M
      Maria PriceSep 12, 2025
      If the fan in your Protemp Heater doesn't operate when plugged in and switched on, and the LED display shows “E1” or “E2”, try these: * Rotate the thermostat to a higher setting. * Inspect all electrical connections.

Protemp PT-45-KF Specifications

General IconGeneral
BrandProtemp
ModelPT-45-KF
CategoryHeater
LanguageEnglish

Related product manuals