EasyManua.ls Logo

Protemp PT-45-KF - User Manual

Protemp PT-45-KF
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Model Numbers
PT- 45-KFA / PT-70T-KFA / PT-75T-KFA / PT-125T-KFA / PT-175T-KFA / PT-215T-KFA
© 2015 Pinnacle Products International, Inc.
668 Stony Hill Road #302 Yardley, PA 19067 USA • Toll Free (800)-641-6996
Fax: (215)-891-8461 • Web: www.protemp.us • Email: info@pinnacleint.com
User’s Manual &
Operating Instructions
CONSUMER: READ AND SAVE THESE INSTRUCTIONS
701000129-15
GENERAL HAZARD WARNING:
READ AND UNDERSTAND ALL OF THE INSTRUCTIONS IN THIS MANUAL
BEFORE ASSEMBLING, STARTING, OR SERVICING THE HEATER. Be sure to comply with the
instructions and warnings provided with this heater. Failure to comply can result in fire or explosion
that can cause property loss, bodily injury, or loss of life. Only persons who can follow and
understand these instructions should operate or service this heater. If you need heater info; such as
an operating manual, labels, etcetera, contact Pinnacle Products International at 800-641-6996.
DANGER
NOT FOR USE IN RESIDENTIAL LIVING AREAS OR IN ENCLOSED SPACES
WITHOUT ADEQUATE VENTILATION. FOR OUTDOOR USE. INDOOR USE
PERMITTED ONLY FOR: THE TEMPORARY HEATING OF ADEQUATELY VENTILATED
BUILDINGS OR STRUCTURES UNDER CONSTRUCTION, ALTERATION OR REPAIR. This is
an unvented portable heater that uses air (Oxygen) from within the area in which it is used. Failure
to provide adequate combustion and ventilation air will result in asphyxiation, carbon monoxide
poisoning, bodily injury or death. Refer to “Ventilation” on Page 7.
DANGER
®
FACTORY ID: 001

Table of Contents

Questions and Answers

  • E
    Erin SheltonSep 13, 2025
    What does error code E3 mean on my Protemp Heater?
    • M
      Michael JonesSep 13, 2025
      If the lamp on your Protemp Heater is flickering and the LED display shows “E3”, the thermostat switch may have failed. Replace the thermostat switch.
  • A
    Alison BenderSep 16, 2025
    Why won't my Protemp PT-45-KF turn on?
    • A
      amanda03Sep 16, 2025
      If your Protemp Heater doesn't turn on and the lamp is not lit, here’s what you can do: * Turn the power switch to “OFF” and allow the heater to cool for 10 minutes before restarting. * Check the power cords and power supply. * Check or replace the fuse. * Inspect all electrical connections.
  • S
    Sabrina AndersonNov 20, 2025
    What to do if my Protemp Heater ignites, but the main PCB shuts off and shows “E1”?
    • J
      Jose BeardNov 20, 2025
      If your Protemp Heater ignites but the main PCB shuts off after a short period, and the LED display shows “E1”, there are several potential causes: * Incorrect pump pressure: Adjust the pump pressure. * Dirty input, output, or lint filter: Clean or replace the air or lint filter. * Dirty fuel filter: Clean or replace the fuel filter. * Dirty nozzle: Clean or replace the nozzle. * Dirty photocell lens: Clean or replace the photocell. * Photocell not installed properly: Adjust the photocell position. * Defective photocell: Replace the photocell. * Improper electrical connection between main PCB and photocell: Check wiring connections. * Improper location of thermister sensor: Check thermister placement. * Improper electrical connection within the temperature limit switch...

Protemp PT-45-KF Specifications

General IconGeneral
BrandProtemp
ModelPT-45-KF
CategoryHeater
LanguageEnglish

Related product manuals