Purelogic HYD-2300

HYD-2100. CNC Plasma&Flame Cutting Control System
Edition of 28.07.2015
34
www.purelogic.ru8 (800) 555 63 74
F1 Common F2 Flame F3 Plasma F4 Powder F5 System F6 Import F7 Export F8 Save
0emit noitingI tsuD .00 s
s00.0emit taeherp tsuD
s00.0emit nepO tsuD esiaR
s00.0emit esolC tsuD esiaR
s00.0emit pU tsuD
s00.0emit nwoD tsuD
mm00.0tesffO latnoziroH tsuD
mm00.0tesffO lacitreV tsuD
F1 Common F2 Flame F3 Plasma F4 Powder F5 System F6 Import F7 Export F8 Save
0emit noitingI tsuD .00 s
s00.0emit taeherp tsuD
s00.0emit nepO tsuD esiaR
s00.0emit esolC tsuD esiaR
s00.0emit pU tsuD
s00.0emit nwoD tsuD
mm00.0tesffO latnoziroH tsuD
mm00.0tesffO lacitreV tsuD
F1 Common F2 Flame F3 Plasma F4 Powder F5 System F6 Import F7 Export F8 Save
mm/n000.521esluP sixA latnoziroH
mm/n000.521esluP sixA lacitreV
mpmm000.0002deeps gnittuc xaM
mpmm000.0006deeps 00G xaM
mpmm000.0003deeps launaM xaM
mpmm000.005timil cra llamS
s04.0emit tsujda emalF
s03.0emit tsujda amsalP
s80.0emit pots ycnegremE
mm000.052deeps tratS
mm000.000001X+ xaM
mm000.000001Y+ xaM
mm000.000001-X- niM
mm000.000001-Y- niM
F1 Common F2 Flame F3 Plasma F4 Powder F5 System F6 Import F7 Export F8 Save
mm/n000.521esluP sixA latnoziroH
mm/n000.521esluP sixA lacitreV
mpmm000.0002deeps gnittuc xaM
mpmm000.0006deeps 00G xaM
mpmm000.0003deeps launaM xaM
mpmm000.005timil cra llamS
s04.0emit tsujda emalF
s03.0emit tsujda amsalP
s80.0emit pots ycnegremE
mm000.052deeps tratS
mm000.000001X+ xaM
mm000.000001Y+ xaM
mm000.000001-X- niM
mm000.000001-Y- niM
Figure 42. Powder parameters Figure 43. System parameters
• Dust Ignition Time: Enter any positive number, unit is s.
• Dust Preheat Time: Enter any positive number, unit is s.
• Raise Dust Open / Close Time: The time of raise dusting port
relatively to the powder port. Enter any positive number, unit is s.
• Dust Up Time: The time for the torch to lift up.
• Dust Down Time: The time for the torch to put down.
• Dust Horizontal Offset: The horizontal displacement of powder gun
relative to the cutting tip.
• Dust Vertical Offset: The Vertical displacement of powder gun
relative to the cutting tip.
SYSTEM PARAMETERS
The system parameters, as showed in Fig 7.5, are related with the
precision of transmission shaft of the machine.
• Horizontal Axis Pulse: The number of pulse that system needs to
generate when the machine move1mm towards X axis, maintaining 3
digits at most after decimal point.
• Vertical Axis Pulse: The number of pulse that system needs to generate
when the machine move 1mm towards Y axis , maintaining 3 digits at
most after decimal point.
• Max Cutting Speed: the maximum cutting speed, unit is mm./m.
• Max G00 speed: the allowable maximum speed when cutting tips idling.
• Small Arc Limit: Maximum speed at cutting a small arc.