EasyManuals Logo

QNAP TS-262 User Manual

QNAP TS-262
79 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #56 background imageLoading...
Page #56 background image
3. Basic Operations
This chapter describes basic NAS operations.
Power Button
Operation User Action Result
Power on Press the button once. The device powers on.
Power o Press and hold the button for 1.5
seconds.
The device powers o.
Force power o Press and hold the button for 5 seconds. The device powers o.
Important
Use this method only when
the device is unresponsive.
Reset Button
Operation User Action Result
Basic system reset Press and hold the
button for 3 seconds.
The following settings are reset to default:
System administrator password: The default password
is the rst MAC address in uppercase letters
without special characters. For example, if the rst
MAC address is 00-08-9B-F6-15-75, then the admin
password would be 00089BF61575.
Tip
You can nd the rst MAC address with
Qnder Pro or attached to a label on the
device listed as MAC1.
The admin account is automatically enabled.
TCP/IP conguration:
Obtain IP address settings automatically via DHCP
Disable jumbo frames
If port trunking is enabled (multi-LAN models
only), the port trunking mode is reset to “Active
Backup (Failover)”.
System port: 8080 (system service port)
Security level: Low (Allow all connections)
LCD panel password: (blank)
VLAN: Disabled
Advanced system
reset
Press and hold the
button for 15 seconds.
The default factory settings are restored.
To retrieve old data after an advanced system reset,
recreate the previous folder structure on the NAS.
TS-x62, TS-x64 User Guide
Basic Operations 55

Other manuals for QNAP TS-262

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the QNAP TS-262 and is the answer not in the manual?

QNAP TS-262 Specifications

General IconGeneral
RAID levels0, 1, JBOD
Hot-swap drive baysYes
Storage drive capacity- GB
Supported file systemsHFS+, NTFS, exFAT, ext3, ext4
Storage drive interface-
Storage drives installedNo
Storage drive sizes supported2.5, 3.5 \
Supported storage drive typesHDD & SSD
Total installed storage capacity0 TB
Number of storage drives installed0
Number of storage drives supported2
Supported storage drive interfacesSerial ATA III
Processor cache4 MB
Processor modelN4505
Processor familyIntel® Celeron®
Processor frequency2 GHz
Processor manufacturerIntel
CPU configuration (max)1
Processor boost frequency2.9 GHz
On-board graphics card modelIntel® UHD Graphics
Flash memory4000 MB
Internal memory4 GB
Concurrent connections1500
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN data rates10, 100, 1000, 2500 Mbit/s
Supported network protocolsIPv4, IPv6
TypeNAS
Device classHome & Home Office
Share folder512
Backup featuresiSCSI LUN
Number of users4096 user(s)
Browser supportedApple Safar, Google Chrome, Microsoft Edge, Mozilla Firefox
Security algorithms256-bit AES, FIPS 140-2
Chassis typeTower
Cooling typeActive
Fan diameter70 mm
Product colorGold, White
LED indicatorsHDD, LAN, Power, Status, USB
Number of fans1 fan(s)
Cable lock slot typeKensington
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)5 - 95 %
Fan voltage12 V
AC input voltage100 - 240 V
Power supply locationExternal
Power consumption (sleep)8.198 W
Power consumption (typical)12.448 W
Power supply unit (PSU) capacity65 W
Operating system version5.0.1
Operating system installedQNAP QTS
Mac operating systems supportedMac OS X 10.10 Yosemite, Mac OS X 10.11 El Capitan, Mac OS X 10.12 Sierra, Mac OS X 10.13 High Sierra, Mac OS X 10.14 Mojave, Mac OS X 10.15 Catalina, Mac OS X 10.15.3 Catalina, Mac OS X 11.0 Big Sur, Mac OS X 12.0 Monterey
Other operating systems supportedIBM AIX 7.1, IBM AIX 7.2, Solaris 10, Solaris 10 SPARC, Solaris 11, Solaris 11 SPARC
Server operating systems supportedWindows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2019
Windows operating systems supportedWindows 10, Windows 10 Education, Windows 10 Education x64, Windows 10 Enterprise, Windows 10 Enterprise x64, Windows 10 Home, Windows 10 Home x64, Windows 10 IOT Core, Windows 10 IoT Enterprise, Windows 10 Pro, Windows 10 Pro x64, Windows 10 x64, Windows 11, Windows 11 x64, Windows 7, Windows 7 Enterprise, Windows 7 Enterprise x64, Windows 7 Home Basic, Windows 7 Home Basic x64, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows 7 x64, Windows 8, Windows 8 Enterprise, Windows 8 Enterprise x64, Windows 8 Pro, Windows 8 Pro x64, Windows 8 x64, Windows 8.1, Windows 8.1 Enterprise, Windows 8.1 Enterprise x64, Windows 8.1 Pro, Windows 8.1 Pro x64, Windows 8.1 x64
Cables includedAC, LAN (RJ-45)
Number of screws12
Weight and Dimensions IconWeight and Dimensions
Depth226 mm
Width105 mm
Height168 mm
Weight1550 g
Package weight2680 g

Related product manuals