RADWAG PUE H315

16
0.2.b.
Aur
PrF, 0.1d, 0.2d, 0.25d,
0.5d, 0.6d, 0.7d, 0.8d,
0.9d, 1d, 2d, 2.5d, 3d,
4d,5d,6d, 7d, 8d, 9d, 10d
Autozero range: PrF - value taken
from program-implemented tables;
0.1d - 10d - value entered directly by
a user.
0.2.c.
Aut
PrF, 0, 0.2s, 0.4s, 0.6s,
1s, 2s, 3s, 4s, 5s, 6s, 7s,
8s, 9s, 10s, 15s, 20s,
Autozero time: PrF - value taken from
program-implemented tables; 0s - 20s
- value entered directly by a user.
0.2.d.
Str
PrF, 0.1d, 0.2d, 0.25d,
0.5d, 0.6d, 0.7d, 0.8d,
0.9d, 1d, 2d, 2.5d, 3d,
4d,5d,6d, 7d, 8d, 9d, 10d
Stability range: PrF - value taken from
program-implemented tables; 0.1d -
10d - value entered directly by a user.
0.2.E.
Stt
PrF, 0, 0.2s, 0.4s, 0.6s,
1s, 2s, 3s, 4s, 5s, 6s, 7s,
8s, 9s, 10s, 15s, 20s,
Stability time: PrF - value taken from
program-implemented tables; 0s - 20s
- value entered directly by a user.
0.2.F.
rAn
YES, no, 50%, dEF
Start mass control: YES – range: from
-10% to +10% of start mass, no – off,
50% – range: from -50% to +50% of
start mass, dEF – range declared in
0.2.G. parameter.
0.2.G.
rnt
10% - 90%
Start mass range in [%].
0.2.H.
Ldn
no, YES
Digit marker for non-verified scales.
0.3.
CAL
-
Adjustment
0.3.1.
CLE
-
External adjustment process.
0.3.2.
Std
-
Determination of start mass for
external adjustment.
0.3.3.
CLI
-
Internal adjustment process.
0.3.4.
Stu
-
Start mass expressed in converter's
divisions.
0.3.5.
AdF
-
Adjustment factor.
0.3.6.
CAC
0.1, 1, 2, 3, 4, 5, 6, 7, 8,
9, 10, 11, 12.
Setting time interval, in [h], after which
internal adjustment is triggered.
0.3.7.
CAt
0.1, 0.2, 0.3, 0.4, 0.5, 0.6,
0.8, 1, 1.5, 2, 2.5, 3, 4, 5,
6, 8, 10
Setting temperature difference, in
[C], for which internal adjustment is
triggered.
0.3.8.
CAS
-
Internal adjustment weight weighing
procedure.
0.3.9.
CAu
-
Internal weight relocation, up-down
direction.
0.3.A
tP
-
Display of current temperature, in
[C].
0.4.
LinE
-
Linearity
0.4.1.
dSG
-
Entering linearity correction points.
0.4.2.
dEL
-
Deleting linearity.