RADWAG PUE C315 - User Manual

44 pages

Save Page as PDF

To Next Page

Main Page

Default Chapter3
- Table of Contents3
1 General Information5
2 Precautions5
- Operation5
- Battery Power Supply5
  - Worn out Batteries Replacement6
3 Warranty Conditions6
4 Design7
- Dimensions7
- Connectors Arrangement8
- Pins Overview8
5 Unpacking and Installation8
6 Start-Up and Operation8
- Levelling8
- Connecting the Scale to the Mains9
- Battery Charge Status9
- Battery Charge Status Check10
7 Maintenance Activities10
- Cleaning ABS Components10
- Cleaning Stainless Steel Components10
8 Operation Panel11
9 Keys11
10 Program Structure12
- Function Groups12
- Operating the Menu12
- Return to the Weighing Mode13
11 Weighing13
- Good Weighing Practice13
- Zeroing14
- Taring14
- Entering Tare Value Manually14
- Dual Range Devices15
- Units15
  - Start Unit15
  - Temporary Unit16
12 Adjustment16
- External Adjustment17
- User Adjustment17
- Adjustment Report18
13 Scale Parameters18
- Filter18
- Value Release19
- Ambient Conditions19
- Autozero Function19
- Tare Function20
- Tare Entering Mode20
- Tare Value Memory21
  - Entering Tare Value to the Weighing Device Memory21
  - Selecting Tare Value from Weighing Device Memory21
- Last Digit22
14 Communication22
- RS232 (1) Port22
- RS232 (2) Port23
- Wireless Communication Module23
15 Peripheral Devices24
- Computer24
- Printer25
  - Printer Port25
- Additional Display25
  - Additional Display Port25
16 Printouts26
- Adjustment Report26
- GLP Printout27
17 Miscellaneous Parameters27
- Automatic Backlight Switch-Off27
- Display Brightness28
- Beep' Sound28
- Automatic Shutdown29
- Date and Time29
- Default Operator Settings29
18 Scale Data30
19 WORKING MODES - General Information30
- Running Working Mode30
- Working Modes Local Settings31
20 Working Mode - Weighing33
- Local Settings33
21 Working Mode - Parts Counting33
- Selecting Operation Mode33
- Setting Sample Mass by Entering Mass of a Single Part34
- Setting Sample Mass by Determining Mass of a Single Part34
22 Working Mode - +/- Control35
- Local Settings35
- Declaring Checkweighing Thresholds35
23 Working Mode - Percent Weighing36
- Local Settings36
  - Selecting Operation Mode36
- Reference Sample Mass Determined by Weighing37
- Reference Sample Mass Determined by Entering the Mass Value37
24 Working Mode - Peak Hold37
- Local Settings37
- Peak Hold Operation37
25 Working Mode - Totalising38
- Local Settings38
- Totalising Operation38
26 Working Mode - Animal Weighing40
- Local Settings40
- Animal Weighing Operation40
27 Diagrams of Connection Cables41
28 Technical Specifications41
29 Troubleshooting42
30 Error Messages43

Other manuals for RADWAG PUE C315

Quick Start12 pages

Startup Guide12 pages

Questions and Answers

H
htrujilloAug 10, 2025
What to do if my RADWAG Accessories scale won't turn on?
- R
  Raymond JenningsAug 10, 2025
  If your RADWAG Accessories scale fails to start, the issue might be due to a disconnected power supply. Ensure the power supply is properly connected to the scale. Alternatively, the battery could be discharged; in this case, connect the power supply to the mains to charge the battery. Finally, verify that the battery is correctly installed with the correct polarization, or that the battery is installed at all.
M
Michelle RichardsAug 25, 2025
Why does my RADWAG Accessories scale keep turning off by itself?
- G
  Garrett BridgesAug 25, 2025
  Your RADWAG Accessories scale might be automatically switching off because the parameter is set to a value that enforces shutdown after a specific time interval. To resolve this, go to the menu and set the parameter to 'nonE'.