Why is the display blank on my Rain Bird Controller?
If the display on your Rain Bird Controller is blank, it could be due to a lack of power. First, check that the main AC power supply is securely plugged in and working properly. Also, make sure the orange power supply wires are connected to the controller's “24 VAC” terminals.
How to fix a blank display on my Rain Bird ESP-TM2?
If the display on your Rain Bird Controller is blank, it likely means the controller isn't receiving power. First, make sure the main AC power supply is securely plugged in and working correctly. Also, check that the orange power supply wires are properly connected to the '24 VAC' terminals on the controller.
What to do if automatic or manual watering won't start on my Rain Bird Controller?
If your Rain Bird Controller isn't starting automatic or manual watering, there are a few potential causes: * A connected rain sensor might be activated. Let the sensor dry out, or disconnect it and replace it with a jumper wire connecting the two SENS terminals. * The jumper wire connecting the two SENS terminals could be missing or damaged. Connect the two SENS terminals on the controller terminal block with a short length of 14 to 18 gauge wire. * A solenoid or master valve might be shorted. If you see a short message on the display, correct the wiring issue. Clear the message by testing watering at the shorted valve or by pressing the button.
Why is the watering icon flashing on my Rain Bird Controller, but the system isn't watering?
If the watering icon is flashing on your Rain Bird Controller but the system isn't watering, it could be due to: * A water supply issue. Make sure there is no disruption to the main water line and that all other water lines are open and functioning. * Loose, improperly connected, or damaged wiring. Ensure the wiring is securely connected at both the controller and in the field. Check for any damage and replace the wiring if needed. Also, inspect wiring connections and replace watertight splice connectors if necessary.
How to fix a frozen display on a Rain Bird ESP-TM2 that won't accept programming?
If your Rain Bird Controller's display is frozen and it won't accept programming, it's possible that an electrical surge has interfered with its electronics. Try unplugging the controller for 2 minutes, then plugging it back in. If there is no permanent damage, the controller should accept programming and resume normal operation. You can also press and release the RESET button.
What to do if the watering icon is flashing, but my Rain Bird ESP-TM2 Controller isn't watering?
If the watering icon on your Rain Bird Controller is flashing but the system isn't watering, there might be a water supply issue. Check that there are no disruptions to the main water line and that all other water supply lines are open and functioning. Another potential cause is loose, improperly connected, or damaged wiring. Ensure the wiring is securely connected at both the controller and in the field, check for any damage, and replace if necessary. Replace wiring connections with watertight splice connectors if needed.
How to fix a frozen display on my Rain Bird ESP-TM2?
If your Rain Bird Controller's display is frozen and it won't accept programming, an electrical surge might have interfered with its electronics. Try unplugging the controller for 2 minutes, then plug it back in. If there's no permanent damage, it should resume normal operation. Also, try pressing and releasing the RESET button.
Why is my Rain Bird ESP-TM2 Controller watering excessively?
Excessive watering with your Rain Bird Controller may occur if programs have multiple, unintentionally set start times. Programs (A, B, or C) only need a single start time to run; separate start times aren't needed for each valve.
Details the key features and specifications of the ESP-TM2 controller.
Explains the LNKTM WiFi Module for remote controller access and configuration.
Provides step-by-step instructions for physically mounting the controller unit to a wall.
Guides users on connecting valve wires, common wires, and master valve wires to the controller terminals.
Instructions for wiring a pump start relay to control the pump for irrigation.
Details how to connect rain or freeze sensors to enable or disable watering based on weather.
Explains how to replace the power cord with custom wiring for power connections.
Identifies and explains the function of each button, dial, and display indicator on the controller.
Guides the user through setting the current date and time on the controller.
Explains how to set up to four distinct watering start times for each program.
Details how to set the duration for each station's watering cycle.
Covers setting watering schedules based on specific days of the week.
Initiates immediate watering for all programmed stations for testing purposes.
Allows manual watering to start for one specific station.
Starts manual watering for a selected program immediately.
Describes the standard automatic watering mode (AUTO RUN) and the OFF mode.
Sets watering schedules to run on odd or even numbered calendar days.
Configures watering to occur at specific intervals, like every 2 or 3 days.
Allows setting the controller to obey or bypass the rain sensor.
Adjusts watering run times by a percentage (5% to 200%).
Suspends automatic watering for a specified period, up to 14 days.
Prevents watering on selected days of the week for specific programming types.
Adds a delay between stations to ensure valve closure before the next opens.
Restores all programmed schedules to the controller's factory default settings.
Allows individual stations to obey or ignore the rain sensor.
Enables saving and restoring current programming settings.
Controls station operation via a master valve or pump start relay.
Sets watering schedules for odd/even days or custom cyclic intervals.
Instructions for using the reset button to troubleshoot controller issues.
Lists available Rain Bird approved accessory devices for the controller.
Provides solutions for common watering problems like no watering or excessive watering.
Offers troubleshooting steps for display problems or frozen controllers.
Statement of compliance with EU directives and relevant harmonized legislation.
Details important safety precautions for installation and use, including wiring warnings.
Information regarding Rain Bird's compliance with the WEEE Directive for product disposal.
Provides web links for controller information and support in multiple languages.
General| Display | LCD |
|---|---|
| Master Valve/Pump Start Circuit | Yes |
| Sensor Inputs | 1 |
| Delay Between Stations | Yes |
| Warranty | 2 years |
| Programs | 3 |
| Watering Duration | 1 minute to 6 hours |
| Valve Output | 24V AC |
| Weight | 2.5 lbs |
| Zones | 6 |
| WiFi Capability | Optional with LNK WiFi Module |
| Start Times | Up to 4 per program |
| Watering Days | Customizable |
| Seasonal Adjust | 5% to 200% in 5% increments |
| Number of Stations | 4, 6, 8 |
| Enclosure | Indoor/Outdoor |
| Stations | 4, 6, 8 |
| Battery Backup | No |
To Next Page
