RCm R. 703 H SACK/1 - User Manual

Questions and Answers

J
John Ramos DVMAug 19, 2025
Why my RCm R. 703 H SACK/1 does not pick up heavy material or leaves dirty traces?
- K
  kelleyrobertSep 12, 2025
  If your RCm Scrubber is not picking up heavy material or leaves dirty traces, it might be due to several reasons: * Brush speed being too slow: Increase the motor speed. * Advancing speed being too high: Decrease the advancing speed. * Brush trail being too light: Adjust the trail. * Worn brush: Lower or replace the brush. * Bristles of the brush are bent or there are wires, strings, etc. bound: Remove the wound material. * Main brush conveyor encrusted by pressed material: Descale with an iron scraper.
B
boltonlarryAug 21, 2025
Why is there excessive dust left by my RCm Scrubber?
- M
  millerjuliaAug 21, 2025
  If you're noticing excessive dust being left on the ground or coming out of the flaps of your RCm Scrubber, here are a few potential causes and solutions: * **Faulty fan:** Check the fan. * **Clogged filters:** Clean the filters. * **Flaps badly adjusted or worn:** Check or replace the flaps. * **Fan speed too slow:** Increase the motor speed.
P
Paul SmithAug 23, 2025
What to do if refuse container loses the refuses on my RCm Scrubber?
- S
  Samuel SmithAug 25, 2025
  If the refuse container on your RCm Scrubber is losing refuses, it could be due to a few reasons: * The container is too full: Empty it more often. * The container is not closed correctly: Close the container properly. * The seal gaskets are broken: Replace the gaskets.
R
Ryan ZunigaAug 26, 2025
Why is there dust presence in the filter housing of my RCm R. 703 H SACK/1 Scrubber?
- A
  anthonyrobinsonAug 26, 2025
  If you find dust in the filter housing of your RCm Scrubber, it could be due to: * Slow filters: Tighten them. * Lack of seals under the filters: Fit seals. * Broken filters: Replace them.
M
monicaboyleAug 28, 2025
What to do if the main brush doesn’t turn on my RCm Scrubber?
- J
  Jackson BarreraAug 28, 2025
  If your RCm Scrubber's main brush isn't turning, it could be due to a broken transmission belt or a belt-stretcher that isn't operating correctly. You should replace the belt or repair the belt-stretcher.
D
Diane LewisAug 29, 2025
How to fix RCm R. 703 H SACK/1 that does not pick up big material?
- J
  Jeffrey ChanAug 30, 2025
  If your RCm Scrubber doesn't pick up big material like paper or leaves, it might be because the front flap lifter isn't working. Repair the possible failure.
B
Bonnie JamesSep 1, 2025
Why RCm R. 703 H SACK/1 Scrubber throws material forward?
- C
  Carolyn WilliamsSep 1, 2025
  If your RCm Scrubber is throwing material forward, it's likely due to a broken front flap. Replace the flap.
S
Stephanie WhiteSep 3, 2025
What causes my RCm R. 703 H SACK/1 Scrubber to not move properly?
- R
  Roger HuntSep 3, 2025
  If your RCm Scrubber is not moving, or it moves laterally, it could be due to: * System without oil: Top up the oil. * Clogged oil filter: Clean the filter. * Open by-pass: Close it.
R
Robert MurphySep 5, 2025
Why the electric vibrator doesn’t work on my RCm Scrubber?
- C
  Colleen BrownSep 5, 2025
  If the electric vibrator on your RCm Scrubber isn't working, it could be due to a broken micro-switch or excessive motor absorption caused by worn charcoals, worn bearings, or a burnt out winding or rotor. Replace the mentioned parts.
H
heather52Sep 7, 2025
How to fix excessive noise of main brush in RCm R. 703 H SACK/1 Scrubber?
- J
  Joseph McintoshSep 7, 2025
  If your RCm Scrubber's main brush is making excessive or alternating noise, it might be because material is wound around the brush. Remove the material.