Reece Series S2 - Needles

NEEDLES
Needles for the Reece Series 32 Machines are packaged and sold in boxes of 100, in the sizes and types listed.
They are of superior struck groove construction, chrome plated and are spotted at the eye except in sizes 00
and finer. When ordering, specify quantity —(100, 200, etc.) and give the Needle E.D.P. Number.
TYPE
APPLICATION
E.D.P. NUMBER
CODE NUMBER
NEEDLE BLADE
SIZE
ROUND POINT
LONG SHANK
Applicable to the majority of woven
fabrics, knits and materials of similar
consistency. These needles have a long
shank that gives added stiffness to the
blade permitting the use of one size
smaller needle than would be normally
required. Cannot be used on heavy
materials that would be penetrated by
the tapered portion of the needle's
shank.
02-0750-1-400
02-0750-1-000
02-0750-1-000
750-LS-0000
750-LS-000
750-LS-00
Extremely Fine
Extra Fine
Very Fine
ROUND POINT
Applicable to the majority of woven
fabrics, knits and materials of similar
consistency.
02-0750-0-110
02-0750-0-111
02-0750-0-112
750-0
750-1
750-2
Fine
Medium
Heavy
BALL POINT
LONG SHANK
Applicable to tightly woven or knitted
fabrics, particularly silks and synthetics
when the fibers of the materials are
subject to damage or fracture by con
ventional Round Point needles. The
Long Shank of this needle gives it the
advantages stated for Round Point
Shank needles.
02-0751-1-400
02-0751-1-000
02-0751-1-000
751-LS-OOOO
751-LS-OOO
751-LS-OO
Extremely Fine
Extra Fine
Very Fine
BALL POINT
Same application as the Long Shank
Ball Point needle above.
02-0751-0-110
02-0751-0-111
751-0
751-1
Fine
Medium
SPEAR POINT
Applicable to fabrics containing a high
percentage of starch or similar sub
stances that tend to cause needle
heating or resistance to proper pulling
up of the stitches.
02-0752-0-110
02-0752-0-111
02-0742-0-112
752-0
752-1
752-2
Fine
Medium
Heavy
SPEAR POINT
DOUBLE GROOVE
The Double Groove needle should be
used only when the conditions justify
it because it casts a smaller loop than
standard needles and may introduce
skipping. For this reason looper points
should be set close to the ne^le blade.
This needle is used on materials that
have a tendency to trap the thread in
its descent into the work which affects
the thread take-up, or causes the thread
to break atthene^le's eye.
02-0752-0-211
02-0752-0-212
752-1-DG
752-2-DG
Medium
Heavy
CROSS POINT
LONG SHANK
Applicable to fine leather and similar
materials as well as some types of
plastics where conventional needles
tend to leave excessive punctures.
This needle permits a higher stitch
density than Round Point needle.
There may be a terxlency in some
cases, for the materials to cling to this
needle, therefore, it should be used
only after comparative test with other
needles. The Long Shank of this
needle gives it the advantages stated
for Round Point Long Shank needles.
02-0753-1-100 753-LS-OO Very Fine
CROSS POINT
The same applications as the Cross
Point Long Shank needle above.
02-0753-0-110
02-0753-0-111
02-0753-0-112
753-0
753-1
753-2
Fine
Medium
Heavy
ROCKED POINT
Applicable to leather and similar
materials where conventional sharp
pointed needles tend to leave exces
sive punctures. The slit made by the
Rocked Point needle will tend to close
up after penetration. Tbis4ieedle per
mits a higher stitch density than is
possible in leather with a round point
needle.
02-0754-0-110
02-0754-0-111
754-0
754-1
Fine
Medium
From the library of: Superior Sewing Machine & Supply LLC