Why is the outside temperature sensor not detected on my REMEHA Quinta Ace 90?
If the outside temperature sensor was expected but not detected on your REMEHA Boiler, connect the sensor or connect the sensor correctly.
Why is the Room Temperature sensor not detected on my REMEHA Quinta Ace 90?
If the room temperature sensor was expected but not detected on your REMEHA Boiler, connect the sensor or connect the sensor correctly.
How to fix poor combustion in REMEHA Quinta Ace 90 Boiler?
Poor combustion in your REMEHA Boiler can stem from several causes. Here's what to check: * Purge the gas supply to remove air if there's a configuration error. * Ensure the gas tap is properly open if there's no flame during operation. * Check the operation and setting of the gas valve unit if there's no ionization current. * Verify that the air inlet and flue gas discharge flues are not blocked. * Confirm that there is no recirculation of flue gases.
What to do if Functional device has been disconnected in REMEHA Quinta Ace 90?
If a functional device has been disconnected from your REMEHA Boiler, check the wiring and connectors if the SCB is not found. If the SCB is faulty, replace it.
What causes Gas Valve Control unit communication exceeding feedback time in REMEHA Boiler?
If the Gas Valve Control unit communication has exceeded feedback time on your REMEHA Boiler, it may be due to a communication error with the security kernel. Try restarting the boiler. If the problem persists, consider replacing the CU-GH.
What does Communication Error occured mean in REMEHA Boiler?
If a Communication Error occurred in your REMEHA Boiler, it could be due to a communication error with the security kernel. In this case, restart the boiler. If the problem persists, replace the CU-GH.
What should I do if Safety parameters level 2, 3, 4 are not correct or missing in REMEHA Quinta Ace 90 Boiler?
If the safety parameters level 2, 3, or 4 are not correct or missing in your REMEHA Boiler, it may be due to a parameter error within the security kernel. Try restarting the boiler. If the issue persists, consider replacing the CU-GH.
What causes Gas Valve Control internal blocking in REMEHA Quinta Ace 90 Boiler?
If a Gas Valve Control internal blocking occurred in your REMEHA Boiler, it could be due to a Security kernel error. Try restarting the boiler. If the problem persists, replace the CU-GH.
What causes No valid data from CU to GVC received error in REMEHA Boiler?
If no valid data from CU to GVC is received in your REMEHA Boiler, it may be due to a communication error with the CU-GH. Restart the boiler.
What to do if Uncritical device has been disconnected in REMEHA Quinta Ace 90 Boiler?
If an uncritical device has been disconnected from your REMEHA Boiler, check the wiring and connectors if the SCB is not found. If the SCB is faulty, replace it.
General| Model | Quinta Ace 90 |
|---|---|
| Category | Boiler |
| Output | 90 kW |
| NOx class | 5 |
| Type | Condensing Boiler |
| Weight | 80 kg |
| Fuel Type | Natural Gas |
| Installation Type | Wall Mounted |
Details the components and functions of the boiler's control panel, including buttons and display.
Instructions for setting up and customizing heating circuit parameters.
Details on configuring domestic hot water temperature and modes.
Details on configuring appliance parameters, heating curves, and screed drying programs.
Steps for commissioning the appliance, including chimney sweep and load tests.
Instructions for updating firmware, resetting, and restoring configuration settings.
Instructions on how to change appliance parameters for optimal performance.
Procedures for checking water pressure, ionisation, connections, and combustion analysis.
Guides on cleaning siphon, components, checking non-return valve, and boiler reassembly.
Details on error code levels (Warning, Blocking, Lock out) with causes and solutions.
To Next Page
