Appendix F • Falk Quadrive Shaft Mounted Drives Model A
(Page 40 of 52) Sizes 5107-5315
378-200 (PN-2128394) Rexnord
January 2019 3001 W. Canal St., Milwaukee, WI 53208-4200 USA
Supersedes 04-17 Telephone: 414-342-3131 Fax: 414-937-4359 www.rexnord.com
Modifications for Non-Standard Mounting Positions
INSTRUCTIONS
For non-standard mountings, modify drives as illustrated
below and on Page 38 to assure satisfactory lubrication.
For applications that exceed the limits shown, drives that
are both rotated AND tilted and drives with backstops,
consult Factory.
CAUTION: Inadequate lubrication will cause damage.
When replacing a pipe plug (P) with a street elbow (E),
insert the plug in the elbow (E/P). When replacing a pipe
plug (P) with a street elbow (E), pipe nipple (N) and a pipe
cap (C), discard the pipe plug. Kits consist of parts for an
oil expansion chamber. Pipe fittings and kits tabulated on
Page 35 are available from Rexnord. Pipe fittings may also
be purchased locally. Use galvanized pipe fittings.
Remove all pipe plugs and coat them and the added parts, with
Permatex #3 or equivalent to prevent leakage. Install parts as
illustrated to suit the mounting position. The air vent must be in
the top of the drive or in the kit standpipe. Fill drives with oil to the
level indicated by the letter “L” in the following drawings.
CW
CCW
STANDARD DRIVE MOUNTING
LIMITS
The standard drive rotation limits from the
basic 3, 6, 9 & 12 o’clock mounting positions
are given in Section I, Page 4. For higher
limits, follow the instructions at the left and the
drawings below (6 o’clock illustrated).
CODE
B — Bushing N — Nipple
C — Cap P — Pipe Plug
E — Street Elbow STD — No Modifications
L — Oil Level
HORIZONTAL DRIVE MODIFICATIONS 20° MAX. DRIVE ROTATION
5 to 20° CW Rotation – Sizes 5107 & 5115
10 to 20° CW Rotation – Sizes 5203 thru 5315
5 to 20° CCW Rotation – Sizes 5203 thru 5315
10 to 20° CCW Rotation – Sizes 5107 & 5115
3 o’clock — CW Rotation 3 o’Clock — CCW Rotation
9 o’Clock — CW Rotation
12 o’Clock — CCW Rotation
12 o’Clock — CW Rotation
9 o’Clock — CCW Rotation
6 o’Clock — CCW Rotation6 o’Clock — CW Rotation
5107 = STD 5115 = .375 E/P 5203 & 5207 = KIT 0786775
5107 = KIT 0738540
5115 = STD 5203 = .375 E/C & .375 X 1.00N
5207 = .375 E/C & .375 X 2.00N
5215 = .500 E/C & .500 X 2.00N
5307 = .500 E/C & .500 X 2.50N
5315 = .500 E/C & .500 X 2.50N
5107 = STD 5115 = .375 E/P
5107 = .375 E/C &
.375 X 3.00N
5115 = KIT 0786775
5203 = .375 E/C & .375 X 1.00N 1.50N
5207 = .375 E/C & .375 X 1.00N 1.50N
5215 = .500 E/C & .500 X 1.12N 1.50N
5307 = .500 E/C & .500 X 1.50N 2.00N
5315 = .500 E/C & .500 X 1.50N 2.00N
5203 thru 5315 = STD
5107 & 5115 = STD
5203 = .375 E/C & .375 X 1.00N
5207 = .375 E/C & .375 X 1.50N
5215 = .500 E/C & .500 X 1.12N
5307 & 4315 = .500 E/C & .500 X 2.00N
5107 = 5-12° STD
5107 = 13-20° .375 E/P
5115 = .375 E/P
5203 & 5207 = KIT 0786775
5215 thru 5315 = KIT 0786776
5107 = .375 E/P 5115 = .375 E/P
5203 & 5207 = KIT 0786775
5215 thru 5315 = KIT 0786776
5-15° 16-20°
5107 & 5115 = KIT 0738540
5203 = .375 E/C & .375 X 1.50N
5207 = .375 E/C & .375 X 2.00N
5215 = .500 E/C & .500 X 2.00N
5307 = .500 E/C & .500 X 2.50N
5315 = .500 E/C & .500 X 2.50N
To Next Page
Loading...
