To Next PageTo Next PageWhy does the [Facsimile] or [Scanner] icon not appear on the [Home] screen of my Ricoh Copier?
If the [Facsimile] or [Scanner] icon does not appear on the [Home] screen of your Ricoh Copier, it could be because functions other than the copier function are not yet ready. Wait a little longer.
Why can't I print in duplex mode on my Ricoh Copier?
You may not be able to print in duplex mode on your Ricoh Copier if you have selected a paper tray that is not set for duplex printing. Change the setting for "Apply Duplex" in System Settings to enable duplex printing for the paper tray. Another reason could be that you have selected a paper type that cannot be used for duplex printing. In [Tray Paper Settings], select a paper type that can be used for duplex printing.
What to do if my Ricoh Copier shows 'Turn main Power Switch off'?
If your Ricoh Copier displays the message 'Turn main Power Switch off', it indicates that the machine did not shut down normally when the main power switch was turned off and then immediately turned on. Turn off the machine, wait for ten seconds or more after shutting it down, and then turn it on again.
What to do if documents do not print out on Ricoh All in One Printer?
If documents and reports from your Ricoh All in One Printer aren't printing, first, check if the paper output tray is full and remove any prints. Also, ensure that the printer has paper loaded. If it doesn't, load paper into the printer.
How to fix Ricoh Copier hardware problem HDD?
If your Ricoh Copier displays the message "Hardware Problem: HDD", it means that an error has occurred in the hard disk. Turn off the main power switch, and then back on again.
How to fix Ricoh Copier hardware problem Ethernet?
If your Ricoh Copier displays the message "Hardware Problem: Ethernet", it means that an error has occurred in the Ethernet interface. Turn off the main power switch, and then back on again.
Why does my Ricoh Copier say 'Please wait.'?
The message 'Please wait' on your Ricoh Copier can appear when you press the [Energy Saver] key, when the machine is warming up, or when you change the toner cartridge. Wait for a while.
What to do if my Ricoh Copier shows 'Memory is full. Do you want to store scanned file?'?
If your Ricoh Copier shows 'Memory is full. Do you want to store scanned file?', it means the scanned originals exceed the number of sheets/pages that can be stored on the hard disk. Press [Yes] to store pages that have been scanned or press [No] if you are not storing pages that have been scanned. Delete unnecessary files by pressing [Delete File].
What to do if my Ricoh Copier is misfeeding frequently?
Frequent misfeeds in your Ricoh Copier can occur if the tray's side or end fences are not set properly. Check that the side or end fences are set properly and that the side fences are locked. Another cause might be paper of undetectable size has been loaded. If you load a paper size that is not selected automatically, you need to specify the paper size with the control panel. A foreign object on the finisher tray can also cause this problem, so ensure the tray is clear.
What to do if my Ricoh Copier display is off?
If the display of your Ricoh Copier is off, the machine may be in Low Power mode. Touch the display panel or press one of the keys on the control panel to cancel Low Power mode. Alternatively, the machine may be in Sleep mode. Press the [Energy Saver] key or the [Check Status] key to cancel Sleep mode.
General| Print Technology | Laser |
|---|---|
| Print Speed | 35 ppm |
| Max Print Resolution | 1200 x 1200 dpi |
| Copy Resolution | 600 x 600 dpi |
| Functions | Print, Copy, Scan, Fax |
| Duplex Printing | Yes |
| Memory (Standard) | 1.5 GB |
| Hard Disk Drive | 250 GB |
| Standard Paper Capacity | 1, 200 sheets |
| Max Paper Capacity | 4, 400 sheets |
| Connectivity | USB 2.0, Ethernet |
| Fax Transmission Speed | 33.6 Kbps (optional) |
| Operating System Compatibility | Windows, Mac, Linux |
| Scan Resolution | 600 dpi |
