RIDGID R4511 User Manual

MANUAL
DEL
OPERADOR
SIERRA
DE
MESA
DE
254
mm
(10 pulgj
R4511
NFORMACON
SOBRE
SERVCIO AL
CONSUMDOR
Para
piezas de repuesto
o servicio, comunhquese
con su
centro
de servicio
autorizado
de productos
RIDGID. Asegürese
de
proporcionar todos
los datos
pertinentes
al llamar o al
presentarse personalmente.
Para obtener información
sobre
el centro de servicio
autorizado más cercano
a
usted,
le
suplicamos
Ilamar al
1-866-539-1710
o visitar nuestro sitio en
Ia red mundial, en Ia
dirección
www.ridgidwoodworking.com.
El nümero
de
modelo
de
este
producto se
encuentra
en una placa
adherida al
alojamiento
del motor.
Le
recomendamos
anotar
el
nümero
de serie
en el espacio
suministrado
abajo. Al
ordenar
piezas de repuesto
siempre
proporcione
Ia siguiente
informaciOn:
Modelo
R4511
OPERATORS
MANUAL
10
in
TABLE
SAW
R4511
Your
newtable saw
has
been
engineered
and
manufactured
to
our
high standards for dependability,
ease
of
operation,
and
operator
safety
When
properly
cared
for,
it will
give
you
years of rugged,
trouble-free performance.
A
WARNING:
To reduce
the
risk
of
injury,
the
user
must
read
and
understand
the operator’s manual
before
using
this
product.
Thank
you for
buying
a
RIDGID®
product.
987000-368
6-27-08
(REV:00)
SAVE
THIS
MANUAL
FOR
FUTURE
REFERENCE
Ntm.
de
serie

RIDGID R4511 Specifications

General

Type	Table Saw
Blade Diameter	10 inches
Max Cut Depth at 90 Degrees	3-1/8 inches
Max Cut Depth at 45 Degrees	2-1/4 inches
Table Size	27 inches x 44 inches
Weight	250 lbs
Arbor Size	5/8 inches
Cut Depth at 90 degrees	3-1/8 inches
Dust Port Size	2-1/2 inches
Bevel Capacity	0 - 45 degrees
Motor Power	15 Amp
Maximum RPM	5000 RPM

Summary

General Safety Rules

Specific Safety Rules

Electrical

Features

Assembly

Unpacking Instructions

Unpack Saw from Shipping Crate

Assemble Leg Stand

Step-by-step guide to assembling the table saw's leg stand.

Assemble Leveling Feet

Adjust Leveling Feet

Install Herc-U-Lift Mobile Base

Guide for attaching the mobile base to the leg stand assembly.

Install Dust Chute

Mount Table Saw to Leg Stand

Procedure for securely mounting the table saw cabinet onto the leg stand.

Install Dust Port

Install Handwheels

Use Herc-U-Lift Mobile Base

Instructions on how to activate and use the mobile base for moving the saw.

Throat Plate Procedures

Install Belt

Step-by-step guide for installing the drive belt for the table saw.

Install and Level Table Extensions

Install Rails

Install Switch Assembly

Secure Ground Bond Strap

Blade and Guard Installation

Procedures for installing the saw blade and the blade guard assembly.

Align Guard

Install Miter Gauge

Install Rip Fence

Blade Adjustments

Install Dust Chute on Assembled Saw

Herc-U-Lift and Uprighting Saw

Steps for reattaching the mobile base and returning the saw to an upright position.

Operation

Basic Operation and Kickback Causes

Overview of fundamental table saw operation, safety, and kickback causes.

Avoiding Kickback

Provides techniques and best practices to prevent kickback during operation.

Types of Cuts

Making Cuts

Make a Cross Cut

Step-by-step instructions for performing a straight 90-degree cross cut.

Make a Rip Cut

Instructions for performing a rip cut along the length of the workpiece.

Make a Miter Cut

Guide for making angled cuts using the miter gauge.

Make Bevel Cuts

Instructions for performing bevel cross cuts and bevel rip cuts.

Make Compound Miter Cut

Guide for performing a cut combining bevel and miter angles.

Make Large Panel Cut

Make Non-Through Cut

Procedure for making cuts that do not go completely through the workpiece.

Make Dado Cut

Instructions for making dado cuts using an optional dado throat plate.

Adjustments

Square Saw Blade to Miter Gauge Groove

Procedure to ensure the saw blade is perfectly aligned with the miter gauge slot.

Set Bevel Indicator and Stops

Guide for setting the bevel indicator and 0/45 degree stop points for accurate angle cuts.

Adjust Miter Gauge

Set Rip Fence Scale Indicator

Maintenance

Troubleshooting

Customer Service Information