What to do if Rigol Inverter screen is dark after pressing the power switch?
If your Rigol Inverter's screen remains dark after pressing the power switch, ensure the power cord is correctly connected and the power switch is actually in the 'on' position. After checking these, try restarting the instrument. If the problem persists, it is recommended to contact RIGOL.
Why Rigol Inverter settings are correct but no waveform is generated?
If your Rigol Inverter is not generating a waveform despite correct settings, verify the following: * The BNC cable is securely connected to the appropriate channel output terminal ([Output]). * The BNC cable isn't damaged internally. * The BNC cable is tightly connected to the test instrument. * The backlight of Output1 or Output2 is on (if not, press the corresponding key). After checking, set the PowerOn option to 'Last' in the Utility ? System menu and restart the instrument. If the issue continues, contact RIGOL.
How to adjust brightness on Rigol Inverter screen?
If the screen of your Rigol Inverter is too dark, check the screen's brightness setting. You can adjust the brightness by going to Utility ? System ? Bright and using the numeric keyboard or knob to set it to a suitable level.
What to do if my Rigol Inverter is locked?
If your Rigol Inverter is locked, it might be in remote mode (indicated by in the status bar). Press Burst to exit remote control. Restarting the generator may also unlock it. Also, check if the front panel keys are locked and unlock them by referring to 'To Lock the Keys'.
Why Rigol Inverter USB storage device cannot be recognized?
If your Rigol Inverter isn't recognizing the USB storage device, first, check if the USB device works normally with other instruments or a PC. Ensure you're using a FAT32 formatted flash-type USB device, as hard drive-based USB storage isn't supported. Try restarting the instrument and re-inserting the USB device. If it still fails, contact RIGOL.
Why Rigol Inverter does not pass the performance verification test?
If the Rigol Inverter fails the performance verification test, verify the following: 1. The generator is within its calibration period (1 year). 2. The generator has warmed up for at least 30 minutes. 3. The ambient temperature is within the specified range. 4. The environment isn't strongly magnetic. 5. The power supplies of the generator and test system are free from strong interference. 6. The test device meets the requirements and is within its calibration period, operating under specified conditions. 7. All connections are tight, and cables are undamaged. 8. Operations align with the performance verification guide, and error calculations are correct. 9. Understand the definition of 'typical value'.
General| Brand | Rigol |
|---|---|
| Model | DG4102 |
| Category | Portable Generator |
| Language | English |
Provides essential safety precautions before operating the instrument to avoid hazards.
Explains warning and caution notices and symbols used throughout the manual for safe operation.
Guides on inspecting packaging, instrument, and accessories for completeness and damage.
Details all controls, connectors, and indicators on the front panel of the DG4000.
Describes the connectors and ports located on the rear panel of the DG4000.
Explains how to connect the instrument to an AC power source using the provided cable.
Illustrates and explains the main components and indicators of the DG4000's display interface.
Details how to input and modify parameters using the numeric keyboard, knob, and direction keys.
Details how to select from the five basic waveform types: Sine, Square, Ramp, Pulse, and Noise.
Instructions on setting the frequency parameter for basic waveforms, including unit selection.
Explains how to set the amplitude for basic waveforms, including Vpp, Vrms, and dBm units.
Guides on setting the DC offset voltage for basic waveforms.
Details how to select built-in, stored, or volatile arbitrary waveforms for output.
Guides on creating new arbitrary waveforms, including setting points and levels.
Guides on editing existing arbitrary waveforms, whether built-in or stored.
Explains how to configure parameters for the fundamental waveform used in harmonic generation.
Explains how to set the start and end frequencies for the sweep range.
Details setting the sweep boundaries using center frequency and frequency span.
Describes the three burst types: N Cycle, Infinite, and Gated.
Guides on activating the counter function and accessing its settings.
Details configuring counter parameters like trigger sensitivity, level, impedance, and coupling.
Explains how to enable and configure statistical analysis of counter measurements.
Covers operations like saving, reading, copying, deleting files, and creating new directories.
Details connecting and controlling the DG4000 remotely via a USB interface.
Explains connecting and controlling the DG4000 remotely via a LAN interface.
Provides steps to diagnose and resolve issues with a dark or blank display.
Offers solutions for poor screen visibility, such as adjusting brightness.
Guides on unlocking the generator when it's in remote mode or keys are locked.
Helps troubleshoot issues where no waveform is output despite correct settings.
Provides steps to resolve problems with USB storage device recognition.
Lists common reasons and checks for failing performance verification tests.
To Next Page
