RKI Instruments EAGLE 2

To Next Page

To Previous Page

EAGLE 2 Operator’s Manual Instrument Description • 7

Figure 2: Component Location, Side View

Figure 3: Component Location, Front & Back

Top Case

Bottom Case

Strap

Case Foot, 6X

Handle

Case Screw, 3X

(Hidden From view)

Buzzer

Inlet Fitting

Exhaust Fitting

Battery Case

Thumbscrew

Charging Jack

Infrared Port

Main Page

Default Chapter3
- Table of Contents3
Chapter 1: Introduction11
- Overview11
- About the EAGLE 211
- Specifications13
- About this Manual14
Chapter 2: Description16
- Overview16
- Instrument Description16
- Standard Accessories25
  - Shoulder Strap25
  - Hose and Probe25
- Optional Accessories26
Chapter 3: Operation32
- Overview32
- Start up32
- Using the Battery Charger for Continuous Operation38
- Measuring Mode, Normal Operation39
- Measuring Mode, Alarms45
- Display Mode50
- Data Logging63
Chapter 4: Calibration Mode65
- Overview65
- Calibration Supplies and Equipment66
- Entering Calibration Mode67
- Calibrating Using the Auto Calibration Method68
  - Setting the Fresh Air Reading68
  - Performing a Span Adjustment in Auto Calibration69
- Calibrating Using the Single Calibration Method74
  - Setting the Fresh Air Reading74
  - Performing a Span Adjustment in Single Calibration75
Chapter 5: Maintenance80
- Overview80
- Troubleshooting80
- Replacing or Recharging the Batteries82
  - Replacing the Batteries82
  - Recharging the Ni-MH Batteries84
- Replacing the Hydrophobic Probe's Particle Filter and Hydrophobic Filter Disk85
- Replacing the Hydrophobic Filter87
- Replacing the Charcoal Filter89
- Checking the Combustible Gas Sensor's Condition90
- Replacing a Sensor90
- General Parts List94
Appendix A: Calibrating with a Sample Bag97
- Overview97
- Calibration Supplies and Equipment97
- Entering Calibration Mode98
- Calibrating Using the Auto Calibration Method99
  - Setting the Fresh Air Reading99
  - Performing a Span Adjustment in Auto Calibration100
- Calibrating Using the Single Calibration Method105
  - Setting the Fresh Air Reading105
  - Performing a Span Adjustment in Single Calibration107
- Parts List111
Appendix B: Setup Mode112
- Overview112
- Tips for Using Setup Mode113
- Using Setup Mode114
Appendix C: Sub Pcbs143
- Overview143
- Description143
- Channel Setup and Sub Pcbs144
  - Sub Pcbs and CONFIGURE CHANNELS144
  - Sub Pcbs and CONFIGURE GASES145
Appendix D: PID Sensors147
- Overview147
- Description147
- Start up and Normal Operation149
- PID Relative Response Feature151
  - PID Sensor Relative Response Screen in Display Mode151
- PID Calibration154
  - Calibrating with a 4-Gas Cylinder and a PID Cylinder154
  - Calibrating with a 5-Gas Cylinder163
- Maintenance171
- Configuring the PID Gas in Setup Mode183
- Parts List189
Appendix E: ESM-01 Toxic Sensors190
- Overview190
- Description190
  - ESM-01 Sensor191
  - ESM-01 Sub PCB192
- Start up and Normal Operation192
- ESM-01 Calibration192
  - Calibrating with a 4-Gas Cylinder and an ESM-01 Cylinder193
  - Calibrating with a 5-Gas Cylinder202
- Maintenance210
  - Replacing the ESM-01 Sensor210
  - Replacing the H 2 S Scrubber in the so 2 and HCN Sensors211
- Parts List213
Appendix F: TC Sensors215
- Overview215
- Description215
  - TC Sensor216
  - TC Sub PCB216
- Start up and Normal Operation217
- Catalytic (LEL) Sensor Screen217
- TC Calibration218
- Maintenance227
  - Replacing the TC Sensor227
- Configuring the TC Gas in Setup Mode228
- Parts List233
Appendix G: Infrared Carbon Dioxide Sensors234
- Overview234
- Description234
- Start up and Normal Operation237
  - Performing a Demand Zero for Carbon Dioxide Sensors237
- Infrared Carbon Dioxide Calibration238
- Maintenance247
  - Replacing the IR CO Sensor or Changing Sensor Type247
- Parts List248
Appendix H: Infrared Methane Sensors249
- Overview249
  - Target Gases249
- Description250
  - Infrared Methane Sensor251
  - Infrared Sub PCB251
- Start up and Normal Operation251
  - Detection Ranges251
- Catalytic (LEL) Sensor Screen251
- Infrared Methane Calibration252
- Maintenance261
  - Replacing the IR Methane Sensor261
- Parts List262
Appendix I: Infrared Hydrocarbon Sensor263
- Overview263
  - Target Gases263
- Description263
  - Infrared Hydrocarbon Sensor264
  - Infrared Sub PCB264
- Start up and Normal Operation265
  - 0-100 %LEL/2.0-30.0 %Vol Autoranging265
- Catalytic (LEL) Sensor Screen265
- Infrared Hydrocarbon Calibration266
- Maintenance275
  - Replacing the IR Hydrocarbon Sensor275
- Parts List276
Appendix J: Methane Elimination Mode277
- Overview277
- Monitoring in Methane Elimination Mode277
- Calibration280
Appendix K: Using the EAGLE 2 in Bar Hole Mode281
- Overview281
- Start Up, Bar Hole Mode281
  - Turning on EAGLE 2, Bar Hole Mode281
  - Performing a Demand Zero, Bar Hole Mode286
- Bar Hole Testing287
  - Performing a Bar Hole Test287
  - Turning off the EAGLE 2, Bar Hole Mode289
Appendix L: Using the EAGLE 2 in Leak Check Mode290
- Overview290
- Start Up, Leak Check Mode290
  - Turning on the EAGLE 2, Leak Check Mode290
  - Performing a Demand Zero, Leak Check Mode295
- Leak Testing295
Appendix M: EAGLE 2 Tank Tester Model298
- Description298
  - Float Probe Assembly299
  - Dilution Fitting (1:1)299
- Start up300
- Alarms302
- Calibration302
- Parts List303
Appendix N: Using the EAGLE 2 in Inert Mode304
- Description304
- Alarms304
- Start up307
- Operation309

RKI Instruments EAGLE 2 - Page 17

Table of Contents

Other manuals for RKI Instruments EAGLE 2

Related product manuals