Robomow MC300 User Manual

35
EN
Screen Seng Descripon Opons
P012
Anti-Theft /
Disabling Device
Change PIN code
• Allows changing of the Anti-Theft / Disabling Device PIN code.
• Enter a new code and then re-enter the new code for conrmation.
0000
P013
Base Station
(Default = ON)
• This option should be used in a Separated Zone which has a
Base Station
• If you have dened more than one zone, then select the relevant
zone before changing the setting.
On/OFF
P014
Add Separated
Zone
• Enables the addition of a Separated Zone.
• L2 is displayed for Separated Zone A – press OK.
• Scroll to set the area of the Separated Zone and press OK.
L2
100
P015
Remove Zone
• Enables the removal of a Separated Zone or a Sub-Zone.
• Choose the Zone you want to remove and press OK.
L2/L3
A1/A2/A3/A4
P016
Sound
(Default = ON)
• Use the Sound option to turn all non-safety sounds off.
On/OFF
P017
Mobile
Communication
System
(Default =
OFF)
• Enables remote communication with the mower using a GSM
Module Accessory, which can be purchased separately.
• For more information, refer to Section 12 – Accessories.
On/OFF
P018
Statistics (Default
= OFF)
• This menu is displayed only if P018 is set to ‘On’.
• Enables to send the operation statistics from the mower to the
manufacturer for diagnostics in case of problems.
On/OFF
P019
Bluetooth Remote
Control Pairing
• Enables the pairing process between your Robomow and
an outdoor Bluetooth Remote Control that is available as an
accessory (Refer to Paragraph 12 Accessories).
P020
Last Termination
Event
• Enables the Behavior View of the special display (may be required
by a Service Station)
P021
Program On/Off
(Default =
OFF)
• This menu enables or disables (pauses) Automatic Operation
either in the main zone (‘L1’), one of the Sub-Zones (‘A1/ A2/ A3/
A4’) or inthe entire lawn (‘All’).
• When Program is set to Off in a particular zone, the mower will
skip the operation in that zone, but will continue to mow all the
other zones
All
L1
A1/A2/A3/A4
On/OFF
P022
Add Sub-Zone
• Enables the addition of a Sub-Zone. Maximal number of Sub-
Zones may be different for each Robomow model.
• A1/A2/A3/A4 (name of the rst available sub-zone) is displayed
– press OK.
• If the mower is not at the Base Station, then ‘U044’ (“Place the
mower in the Base Station”) is displayed. Place the mower in the
Base Station and press OK.
• The mower will start moving towards the Sub-Zone. ‘U041’ (“Press
the STOP button at Sub-Zone entry.”) will be displayed.
• Press ‘STOP’ button, when the mower is at any point beyond the
Narrow Pass and inside the Sub-Zone (Entry Point).
• Scroll to set the area of the Sub-Zone and press OK.
• Note! This process is not a part of the One-Time Setup (see
Section 5.2)
• The area setting of a Sub-Zone can be later updated through the
‘Area’ menu of the Basic Settings (see Section 6.4.1)
• The distance to Sub-Zone’s entry point can later be update
through menu P023
A1/A2/A3/A4
100
P023
Update Distance
To Sub-Zone
• This menu is shown only if a Sub-Zone has been dened.
• It allows to update the distance to Sub-Zone’s entry point.
• Scroll to choose the required Sub-Zone (A1/A2/A3/A4) and press
OK to update the distance to the entry point.

Robomow MC300 Specifications

General

Type	Robotic lawn mower
Cutting width	280 mm
On/off switch	Yes
Cutting system	-
Recommended lawn area	300 m²
Maximum cutting height	60 mm
Minimum cutting height	15 mm
Grass collecting volume	- L
Battery type	LiFePO4
Power source	Battery
Battery voltage	26 V
Battery technology	Lithium

Weight and Dimensions

Depth	460 mm
Width	630 mm
Height	210 mm
Weight	11100 g