Robomow MC300 User Manual

41
EN
Display Message Probable Cause/Event Correcve Acons
0016
Low
temperature
- Mower does not depart
automatically from the Base Station
when the ambiance temperature is
lower than 5ºC (41ºF).
- Information – When the temperature
is below 5ºC (41ºF) the grass does
not grow or grows very slowly.
However Manual Depart is enabled.
- No need to do anything.
- Robomow will renew the operation
automatically as soon as the ambiance
temperature will rise above 5ºC (41ºF).
0020
Rain detected
- The operation is delayed as
Robomow detects rain.
- Robomow should resume operation
30 minutes after it stops to detect
the rain.
- No need for action.
- The message is displayed until Robomow will
not detect rain and then will start mowing.
0021
Check mowing
height
- Mowing motor has faced over-
current conditionsfor too long as a
result of high grass or an obstacle
that is stuck or wrapped around the
blade.
- Something is preventing a blade
from rotating freely.
- Severe grass accumulation under
the mowing deck, rope, or similar
object is wrapped around mowing
blade.
- CAUTION – Switch Off the Safety Switch
before checking the blade.
- Inspect the blade for foreign material or debris
preventing rotation.
- Clean out accumulated grass clippings using
a wooden stick.
0022
Check mowing
motor
- Mowing motor has faced over-
current for too long in the Base
Station before starting the operation.
- CAUTION – Switch Off the Safety Switch
before checking the blade.
- Remove the mower from the Base Station.
Inspect the blade for foreign material or debris
preventing rotation.
0023 Check power - See E4 in the above table
0026 Base problem
- Robomow fails to enter the Base
Station several consecutive times.
- Adjust the Base Station position.
- Clean the contacts with a brush or piece of
cloth.
0027 Start Elsewhere
- Drive wheel motors have been
working under severe load during
automatic or manual operation.
- Check to insure the mower is not stuck,
causing the drive wheels to slip.
- Check the ground around the mower for holes
or indentations. Fill with dirt and level off.
- Check if the drive wheels are free to rotate
and nothing is blocking them.
- Remove the mower away from this particular
location and restart operation.
0028 Cross Outside
- The Perimeter Wire is too close to
the edge.
- The lawn slope is too big.
- Robomow does not succeed to
turn in place at the edge and it
causes the mower to slip out of the
designated area.
- Robomow has slipped out of the
Perimeter Wire lope because of
sloping area or wet grass.
- Remove the wire towards the inner part of the
lawn.
- Do not include this area because of its steep
slopes.
- Fill holes and pits in the ground.
- Increase the cutting height.
0030 Start Inside
- Automatic operation is initiated
while the robot is placed out of the
Perimeter Wire loop.
- Place the mower inside the lawn and renew
the operation.
0031 Stuck in place - See E1 in the above table
0060
Check mowing
hours (%)
- The mowing hours % value you
have set is too high for your lawn
area.
- Decrease the mowing hours % you have set
for the zone(s) in your lawn.
0061
Decrease
Inactive Time
- See E8 in the above table

Robomow MC300 Specifications

General

Type	Robotic lawn mower
Cutting width	280 mm
On/off switch	Yes
Cutting system	-
Recommended lawn area	300 m²
Maximum cutting height	60 mm
Minimum cutting height	15 mm
Grass collecting volume	- L
Battery type	LiFePO4
Power source	Battery
Battery voltage	26 V
Battery technology	Lithium

Weight and Dimensions

Depth	460 mm
Width	630 mm
Height	210 mm
Weight	11100 g