EasyManuals Logo

Robomow MC300 User Manual

Robomow MC300
52 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #44 background imageLoading...
Page #44 background image
44
Problem
Encountered
Probable Cause/Event Correcve Acons
Uneven mowing
results
- The time between operations is too long
because of long inactive time windows.
- Minimize the Inactive Time windows to allow
Robomow to complete the Mowing Cycle faster
and to achieve even mowing results.
- Grass is growing very fast.
- - If it is during a fast growing season – change
the Mowing Frequency (refer to Section 6.4.2 –
P001).
- The shape of the lawn is complicated
(Narrow Passages, obstacle and islands).
- In a complicated lawn more time is required for
the lawn to achieve better mowing results.
- Increase the mowing hours percentage (refer to
Section 4.3.2.1).
- The set area is smaller than the actual
lawn size.
- Increase the zone area (refer to Section 4.3.3
Edit an existing Zone).
Robomow
operates during
Inactive Time.
- Wrong clock time is set in the mower.
- Verify that the time on the mower is set correctly.
- Set the time (refer to Section 4.4.4).
- Reset the Inactive Time (refer to Section 4.3.1).
Robomow
operates during
rain
- Rain Sensor is disabled or its sensitivity
is set too low
- Enable the Rain Sensor and adjust its sensitivity
if required (refer to Section 6.4.2 – P007/p008)
- The Islands feature is set to On. In this
case the mower is searching for the base
by moving around the lawn. This special
search method takes more time, and
may create an impression that the mower
is still mowing, while in fact it is already
searching for the Base Station.
- No special action is required. For more
information about the Islands On/Off feature
refer to Section 6.4.2 – P002)
Cut wire indicator
is ashing on
Power Box
- The Extension Cable is disconnected or
damaged between Power Box and the
Base Station.
- Conrm the Extension Cable is plugged in and
wire leads are rmly attached.
- Perimeter Wire is cut.
- Walk along Perimeter Wire.
- Look for cuts or breaks in the wire.
- Repair with Robomow wire splice connectors.
The poor
connection
indicator is
ashing on
Power Box
- Poor connections
- Check and repair all loose, poor, or corroded
connections.
- Twisted cables or a screw terminal which
is insulated with insulation tape is not a
satisfactory splice.
- Soil moisture causes the conductors to
oxidize.
- Use the connectors supplied in the box. They
are waterproof and give a reliable electrical
connection.
9.4.1 Description of No-Depart Codes
Code Descripon Correcve Acon
00
None. Automatic departure is working properly None. Wait for the end of current charging cycle
01
Mower’s battery is not yet in the required state
forautomatic departure
None. Wait for the end of current charging cycle.
May take longer than usual
02
Inactive Time is activated. No automatic
departure during Inactive Time
None. Validate Inactive Time settings (see
Section 6.4.1)
03
Mowing cycle is completed. Waiting for the next
scheduled operation
None
04
Humid conditions or rain were detected during
last 30 minutes.
- None. If the rain has stopped, wait at least for
another 30 minutes.
- If it there was no any raining at all, consider
adjusting rain sensor’s sensitivity (see P008 in
Section 6.4.2) or call Robomow Hotline
05
The mower is switched off Switch on the Safety Switch
07
User response (interaction) is required in order to
continue current operation
Acknowledge the error message
08
Multiple consecutive mowing operations were
shorter than expected. Usually accompanied by
U018 (“Operation time is shorter than expected”)
- Inspect mower’s blade and drive wheels.
- Battery run-time may be too short.

Table of Contents

Other manuals for Robomow MC300

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Robomow MC300 and is the answer not in the manual?

Robomow MC300 Specifications

General IconGeneral
TypeRobotic lawn mower
Cutting width280 mm
On/off switchYes
Cutting system-
Recommended lawn area300 m²
Maximum cutting height60 mm
Minimum cutting height15 mm
Grass collecting volume- L
Battery typeLiFePO4
Power sourceBattery
Battery voltage26 V
Battery technologyLithium
Weight and Dimensions IconWeight and Dimensions
Depth460 mm
Width630 mm
Height210 mm
Weight11100 g

Related product manuals