Robomow RC306 User Manual

37
EN
Screen Seng Descripon Opons
P008
Rain Sensor
Sensitivity
(Default = 2)
• ThismenudenesRainSensor’ssensitivity.
• The numbers in the menu represent the following levels of sensitivity:
1 – LOW
2 – MEDIUM
3 – HIGH
• The higher the Sensitivity setting, the more sensitive Robomow is to
rain detection.
1/2/3
P009
Edging On/Off
(Default = ON)
• Edging is a special mode, in which Robomow follows the perimeter
wire for complete and accurate mowing of the lawn edges.
• In lawns where the edge is not maintained well and the mower fails
to complete the drive along the edge of the lawn, it is recommended
to set Edging to ‘Off’.
• Setting Edging to ‘Off’ disables Edging mode in automatic departures
from the station, but still allows edge-mowing when pressing the
‘Edge’ mode button on the operating panel.
On/OFF
P010
Child Lock
(Default = OFF)
• The Child Lock feature locks the buttons to prevent unintended
operation, especially by children and pets.
• If the Child Lock is set to ‘On’, to operate the mower it is required to
rstpressoneoftheoperatingmodebuttonsandthentopressthe
OKbuttontoconrm.
On/OFF
P011
Anti-Theft /
Disabling Device
(Default = OFF)
• The Anti-Theft / Disabling Device feature alarms the surroundings
in the event of an unintended use or removal of the mower from its
designated area.
• ToturntheAnti-Theft/DisablingDeviceOnforthersttime,setitto
‘On’ and choose a PIN code of 4 digits.
Tip: Select a number you can remember. Write it down (bottom of
Chapter 10), and keep it in a safe place.
• When the Anti-Theft / Disabling Device system is activated, 0000 will
be displayed. Enter your 4-digit code to deactivate the Anti-Theft /
Disabling Device.
• If the code is not entered, then the message is changed to U062
(Alarm will soon be activated). Enter the code, otherwise the alarm
will start.
ON/OFF
1234
P012
Anti-Theft /
Disabling Device
Change PIN code
• Allows changing of the Anti-Theft / Disabling Device PIN code.
• Enteranewcodeandthenre-enterthenewcodeforconrmation.
0000
P013
Base Station
(Default = ON)
• This option should be used in a Separated Zone which has a
Base Station
• Ifyouhavedenedmorethanonezone,thenselecttherelevant
zone before changing the setting.
On/OFF
P014
Add Separated
Zone
• Enables the addition of a Separated Zone.
• L2 is displayed for Separated Zone A – press OK.
• Scroll to set the area of the Separated Zone and press OK.
L2
100
P015
Remove Zone
• Enables the removal of a Separated Zone or a Sub-Zone.
• Choose the Zone you want to remove and press OK.
L2/L3
A1
/A2/A3/
A4
P016
Sound
(Default = ON)
• Use the Sound option to turn all non-safety sounds off.
On/OFF
P017
Mobile
Communication
System
(Default = OFF)
• Enables remote communication with the mower using a GSM
Module Accessory, which can be purchased separately.
• For more information, refer to Section 12 – Accessories.
On/OFF
P018
Statistics (Default
= OFF)
• This menu is displayed only if P018 is set to ‘On’.
• Enables to send the operation statistics from the mower to the
manufacturer for diagnostics in case of problems.
On/OFF

Robomow RC306 Specifications

General

Type	Robotic lawn mower
Cutting width	280 mm
Cutting system	-
Recommended lawn area	600 m²
Maximum cutting height	60 mm
Minimum cutting height	15 mm
Grass collecting volume	- L
Battery type	LiFePO4
Power source	Battery
Charging time	1 h
Battery voltage	26 V

Weight and Dimensions

Depth	460 mm
Width	630 mm
Height	210 mm
Weight	11400 g