Robomow RC306 User Manual

36
Screen Seng Descripon Opons
P002
Islands
(Default =
OFF)
• In case there is a large perimeter island (a swimming pool, a pond, a
largeowerbed,etc.)inaparticularzone,itisrecommendedtoset
this setting to On. This will prevent the mower from following the wire
around such island, while returning to the Base Station.
• When the Islands feature is set to On, the mower will execute a
special method of searching for the Base Station. As a result it may
take the mower more time to arrive to the Base Station.
• See also menu P006 below.
On/OFF
P003
Near Wire Follow
(Default =
ON)
• When Robomow completes its operation, or when the ‘Home’ button
instructs it to Go To Base, it drives itself to the Base Station.
• Robomow drives along the Perimeter Wire with a dynamic offset (not
centered) to prevent wheel tracks along the same path. This return
behavior can be turned off.
• This menu is not available for RC304u and RC304 Pro models.
• For all other models, the Near Wire Follow feature can be enabled
andconguredforaSub-Zoneaswell.
On/OFF
P004
Max Near Wire
Follow Distance
(Default =
changed based on
the lawn area)
• The maximum distance Robomow will drive from the wire when
returning to the Base Station.
• The distance does not represent actual units of measurement.
• The offset Distance values range from 1 to 12. They represent
different distances from the wire.
• The higher the Distance setting, the smaller the probability of tracks
along the perimeter.
• Perimeter Islands that are relatively close to the Perimeter Wire or
narrow passages may prevent the mower to complete its drive to the
Base Station with ‘Near Wire Follow’ mode. In such cases decrease
the distance to allow the mower to complete the drive to the Base
Station.
• This menu is not available for RC304u and RC304 Pro models.
• For all other models, the Near Wire Follow feature can be enabled
andconguredforaSub-Zoneaswell.
1-12
P005
Min Near Wire
Follow Distance
(Default = 1)
• The minimum distance Robomow will drive from the wire when
returning to the Base Station.
• The larger the number, the bigger the distance the mower will drive
from the wire while returns to the Base Station.
• This menu is not available for RC304u and RC304 Pro models.
• For all other models, the Near Wire Follow feature can be enabled
andconguredforaSub-Zoneaswell.
1-5
P006
Near Wire Follow
Test
• Enables to test the mower in the max ‘Near wire Follow Distance’
thatisdenedinmenuP004.
• If the mower is not able to complete the drive in ‘Near Wire’ mode
smoothly, then it is recommended to reduce the max distance set in
menu P004.
• This menu is not available for RC304u and RC304 Pro models.
P007
Rain Sensor
(Default = On)
• The Rain Sensor feature halts operation on rainy or highly humid
weather.
• This is recommended for the health of the lawn. However, mowing
wet grass does not present any technical problem.
Note! It may take a few minutes before Robomow detects rainy or
humid conditions. This is done in order to avoid false-detections. As
soon as the mower detects rain, it halts current mowing operation
and starts searching for the Base Station. When the ‘Islands’ feature
is set to On (see menu P002 above), the mower will execute a special
method of searching for the Base Station. As a result it may take the
mower more time (up to 20-30 minutes) to arrive to the Base Station.
On/OFF

Robomow RC306 Specifications

General

Type	Robotic lawn mower
Cutting width	280 mm
Cutting system	-
Recommended lawn area	600 m²
Maximum cutting height	60 mm
Minimum cutting height	15 mm
Grass collecting volume	- L
Battery type	LiFePO4
Power source	Battery
Charging time	1 h
Battery voltage	26 V

Weight and Dimensions

Depth	460 mm
Width	630 mm
Height	210 mm
Weight	11400 g