EasyManua.ls Logo

Roland FC-100mkII - Troubleshooting; Power Issues; Sound Output Problems; Patch Change Issues

Roland FC-100mkII
32 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
3.
Troubleshooting
Symptom
Cause
What
to
do
The
power
cannot be turned on.
o The
connected
unit
is
not
switched
on.
SW'lteh on
the
connected
unit.
o The RRe cable
IS
disconnected.
Connect the
RRC
cable securely until
it
is
locked.
o The RRC cable is
not
connected
correctly.
Make
sure
thatthe
RRC
IN
is
connected
to
RRCOUT.
The
unit
connected
to
the
FC-100MK
n
o The
volume
of
the
expression
pedal
Move
the pedal slowly.
does
not
generate
any
sound.
assigned
for
Volume is set
to
zero.
D The Control Pedal
set
to
Mute
is
working
Lower
the volume
of
the amplifier,
then
press
the Control PedaL
Patches on the connected device o The
connected
device
is
not
set
to
the
Set
the
connected
device
to
the
appropriate
cannot
be changed.
appropriate
mode
for
Patch
selection,
mode
that
allows
you
to
change Patches.
o The
MIDI
channels
are
not
set
correctly.
Set
the
MIDI
channel
of
the FC-100MK n
to
the
same
number
as
the
connecled
device.
The
Control Pedal does
not
work
o The
mode
is
not
set
correctly.
Set the
mode
correctly.
properly.
o The
mode
(Latch
or
Unlatch)
of
the
Control
Change
the
position
of
the
Mode
Selector
Pedal is
not
set
correctly.
Switch
on
the
rear
of
the unit.
a The
Control
number
is
not
set
correctly.
Set
the
Control
Number
properly.
(Page 11)
o The
connnected
device
does
not
recognize
Set
the
connected
device
so
that
it
can
the
messages
of
the
set
Control
Number.
I recognIZe
the
messages .
...
The device you are
using
may
be incapable of
i recognizing the
messages
.
The
expression
pedal
does
not
o The
expression
pedal
is
not
connected
..
!
Connect
the
expression pedal securely
to
the
function
properly.
properly.
I
approori"e
jack
Note
that
the
EXP1
and EXP2
jacks
functlon
dlfferer:tly.
o The
expression
pedai
is
not
adjusted
Adjust
the
minimum
volurne
of
the
expression
correctly. pedal.
o
MID!
channels
are
not
set
correctly.
Set
the
MIDI
channel
of
the
FC-1
DOMK
IT
to
the
same
number
as
the
connected
device.
Wage 10)
o The
Control
number
is
not
set
correctly,
Set
the
Comrol
Number
properly.
(Page 11)
a
The
connected
device
does
not
recognize
Set
the
connected
device
so
that
it
can
the
messages
of
the
relevant
Control
Pedal.
recognize
the
messages.
*
The
device
you are using
may
be incapable
of
recognizing the
messages.
The
Tuner
Out
does
not
function,
o You are
using
the
RMC~
1.
The
Tuner
Out
cannot
be
used in such cases as
at
leh.
a
The
unit
you
use
is
not
compatible
with
the
Tuner
Out
of
the
FC~
1
OOMK
n.
20

Table of Contents

Related product manuals