145
Parameter List
VOICE PRIORITY* Voice Priority LAST, LOUDEST
KEY RANGE LOWER * Key range Lower C-1 - UPR
KEY RANGE UPPER * Key range Upper LWR - G9
VELO RANGE SW* Velocity Range Switch OFF, ON
VELO RANGE LOW Velocity Range Lower 1 - UPR
VELO RANGE UP Velocity Range Upper LWR - 127
VELO CROSS FADE Velocity Cross Fade 0 - 127
*: Common settings for each tone
SOLO: , PORTAMENT: [PTN]+[F1 (PACH) ]+[F1 (EDIT) ]+[F2 (CMN) ]+[F2 (SOLO) ] (P. 102)
Parameter Parameter Name Setting Value
SOLO SW Solo Switch OFF, ON
SOLO LEGATO Solo Lagato OFF, ON
SW Portamento Switch OFF, ON
MODE Portamento Mode NORMAL, LEGATO
TYPE Portamento Type RATE, TIME
START Portamento Start PITCH, NOTE
TIME Portamento Time 0 - 127
MOD: [PTN]+[F1 (PACH) ]+[F1 (EDIT) ]+[F3 (CTL1) ]+[F1 (MOD) ] (P. 103)
Parameter Parameter Name Setting Value
CONTROL1 DEST Control1 Destination 1*
CONTROL1 DEPTH Control1 Depth -63 - +63
CONTROL2 DEST Control2 Destination 1*
CONTROL2 DEPTH Control2 Depth -63 - +63
CONTROL3 DEST Control3 Destination 1*
CONTROL3 DEPTH Control3 Depth -63 - +63
CONTROL4 DEST Control4 Destination 1*
CONTROL4 DEPTH Control4 Depth -63 - +63
1*: OFF, PCH, CUT, RES, LEV, PAN, L1P, L2P, L1F, L2F, L1A, L2A, PL1, PL2, L1R, L2R
BEND: [PTN]+[F1 (PACH) ]+[F1 (EDIT) ]+[F3 (CTL1) ]+[F2 (BEND) ] (P. 103)
Parameter Parameter Name Setting Value
BEND RANGE UP * Bend Range Up 0 - +12
BEND RANGE DOWN * Bend Range Down 0 - -48
CONTROL1 DEST Control1 Destination 1*
CONTROL1 DEPTH Control1 Depth -63 - +63
CONTROL2 DEST Control2 Destination 1*
CONTROL2 DEPTH Control2 Depth -63 - +63
CONTROL3 DEST Control3 Destination 1*
CONTROL3 DEPTH Control3 Depth -63 - +63
CONTROL4 DEST Control4 Destination 1*
CONTROL4 DEPTH Control4 Depth -63 - +63
*: Common settings for each tone
1*: OFF, PCH, CUT, RES, LEV, PAN, L1P, L2P, L1F, L2F, L1A, L2A, PL1, PL2, L1R, L2R
AFT: [PTN]+[F1 (PACH) ]+[F1 (EDIT) ]+[F4 (CTL2) ] (P. 103)
Parameter Parameter Name Setting Value
CONTROL1 DEST Control1 Destination 1*
CONTROL1 DEPTH Control1 Depth -63 - +63
CONTROL2 DEST Control2 Destination 1*
CONTROL2 DEPTH Control2 Depth -63 - +63
CONTROL3 DEST Control3 Destination 1*
CONTROL3 DEPTH Control3 Depth -63 - +63
CONTROL4 DEST Control4 Destination 1*
CONTROL4 DEPTH Control4 Depth -63 - +63
1*: OFF, PCH, CUT, RES, LEV, PAN, L1P, L2P, L1F, L2F, L1A, L2A, PL1, PL2, L1R, L2R