Roland Groovebox MC-307

147
Parameter List
A-ENV: [PTN]+[F1 (PACH) ]+[F1 (EDIT) ]+[F4 (AMP) ]+[F2 (AENV) ] (P. 110)
Parameter Parameter Name Setting Value
VELO SENS Velocity Sence -100 - +150
VELO TIME SENS Velocity Time Sence 1*
TM1 Time1 (Attack Time) 0 - 127
TM2 Time2 0 - 127
TM3 Time3 (Decay Time) 0 - 127
TM4 Time4 (Release Time) 0 - 127
LV1 Level1 0 - 127
LV2 Level2 0 - 127
LV3 Level3 (Sustain Level) 0 - 127
1*: -100, -70, -50, -40, -30, -20, -10, 0, +10, +20, +30, +40, +50, +70, +100
BEND: [PTN]+[F1 (PACH) ]+[F1 (EDIT) ]+[F1 (BEND) ]+[F1 (BEND) ] (P. 112)
Parameter Parameter Name Setting Value
BEND RANGE Bend Range 0 - +12
SEND: [PTN]+[F1 (PACH) ]+[F1 (EDIT) ]+[F1 (BEND) ]+[F2 (SEND) ] (P. 112)
Parameter Parameter Name Setting Value
REV SEND LEVEL Rhythm Tone Reverb Send Level 0 - 127
DLY SEND LEVEL Rhythm Tone Delay Send Level 0 - 127
M-FX SW Rhythm Tone M-FX Switch OFF, ON
■ Setup Parameter
*: Parameters that are set independently for each part.
PART MIXER: [PTN]+[F2 (STUP) ]+[F1 (PART) ] (P. 22)
Parameter Parameter Name Setting Value
LEVEL * Part Level 0 - 127
PAN * Part Pan L64 - 63R
KEY SHIFT * Part Keyshift -48 - +48
REV LEVEL * Part Reverb Level 0 - 127
DLY LEVEL * Part Delay Level 0 - 127
M-FX OUT * Part M-FX Switch OFF, ON, RHY (RHY: Part R Only)
SEQ OUT * Sequencer Output Assign INT, EXT, BOTH
REVERB: [PTN]+[F2 (STUP) ]+[F2 (REV) ] (P. 42)
Parameter Parameter Name Setting Value
TYPE Reverb Type ROOM1, ROOM2, STAGE1, STAGE2, HALL1, HALL2
TIME Reverb Time 0 - 127
HF DAMP HF Damp 1*
REVERB LEVELl Reverb Level 0 - 127
M-FX TO REV LEVEL M-FX to Reverb Level 0 - 127
1*: 200, 250, 315, 400, 500 ,630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000, BYPASS
DELAY: [PTN]+[F2 (STUP) ]+[F3 (DLY) ] (P. 44)
Parameter Parameter Name Setting Value
TYPE Delay Type SHORT, LONG
TIME Delay Time S:0.1 - 275, L:200 - 1000, 1*
FEEDBACK Feedback Level 0 - +98
HF DAMP HF Damp 2*
OUTPUT Delay Output Assign LINE, REV, LINE + REV
M-FX TO DLY LEVEL M-FX to Delay Level 0 - 127
DELAYLEVEL Delay Level 0 - 127
1*:
2*: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000, BYPASS
M-FX TYPE: [PTN]+[F2 (STUP) ]+[F4 (M-FX) ] (P. 48)
Parameter Parameter Name Setting Value
M-FX TYPE: M-FX Type 1 4-BAND EQ, 2 SPECTRUM, 3 ENHANCER, 4 ENHANCER, 5 OVERDRIVE,
6 DISTORTION, 7 LO-FI, 8 NOISE, 9 RADIO TUNING, 10 COMPRESSOR,