Roland juno-ds61 - MFX;Chorus;Reverb Parameters; Equalizer and Spectrum Effects; Isolator and Step Reset Effects

41
MFX/Chorus/Reverb Parameters
When Using 3D Eects
The following 3D eects utilize RSS (Roland Sound Space) technology to create a
spaciousness that cannot be produced by delay, reverb, chorus, etc.
5
52: 3D DELAY
5
29: 3D CHORUS
5
30: 3D FLANGER
5
31: 3D STEP FLANGER
When using these eects, we recommend that you place your speakers as follows.
Also, make sure that the speakers are at a sucient distance from the walls on either
side.
30˚ 30˚
If the left and right speakers are too far apart, or if there is too much reverberation,
the full 3D eect may not appear. Each of these eects has an “Output Mode”
parameter. If the sound from the OUTPUT jacks is to be heard through speakers,
set this parameter to “SPEAKER.” If the sound is to be heard through headphones,
set it to “PHONES.” This will ensure that the optimal 3D eect will be heard. If this
parameter is not set correctly, the full 3D eect may not appear.
About the Step Reset function
5
06: STEP FILTER
5
16: STEP RING MOD
5
19: STEP PAN
5
20: SLICER
5
63: STEP PCH SHIFTER
The above types contain a sixteen-step sequencer. For these types, you can use a
MFX control to reset the sequence to play from the rst step. To do this, set the MFX
control Destination to “Step Reset.”
For example if you are using the modulation lever to control the eect, you would
make the following settings.
Parameter Value
Source CC01: Modulation
Destination Step Reset
Sens +63
With these settings, the sequence will play back from the rst step whenever you
operate the modulation lever.
Rotary eect
5
21: ROTARY
5
22: VK ROTARY
When performing sounds that use these eects, you can change the speed of the
rotary eect by moving the modulation lever away from yourself.
01: EQUALIZER
This is a four-band stereo equalizer (low, mid x 2, high).
L in
R in
L out
R out
4-Band EQ
4-Band EQ
Parameter Value Explanation
Low Freq 200, 400[Hz] Frequency of the low range
Low Gain # -15–+15[dB] Gain of the low range
Mid1 Freq 200–8000[Hz] Frequency of the middle range 1
Mid1 Gain -15–+15[dB] Gain of the middle range 1
Mid1 Q 0.5, 1.0, 2.0, 4.0, 8.0
Width of the middle range 1
Set a higher value for Q to narrow the
range to be aected.
Mid2 Freq 200–8000[Hz] Frequency of the middle range 2
Mid2 Gain -15–+15[dB] Gain of the middle range 2
Mid2 Q 0.5, 1.0, 2.0, 4.0, 8.0
Width of the middle range 2
Set a higher value for Q to narrow the
range to be aected.
High Freq 2000, 4000, 8000[Hz] Frequency of the high range
High Gain # -15–+15[dB] Gain of the high range
Level # 0–127 Output level
02: SPECTRUM
This is a stereo spectrum. Spectrum is a type of lter which modies the timbre by
boosting or cutting the level at specic frequencies.
L in
R in
L out
R out
Spectrum
Spectrum
Parameter Value Explanation
Band1 (250[Hz])
-15–+15[dB]
Gain of each frequency band
Band2 (500[Hz])
Band3 (1000[Hz])
Band4 (1250[Hz])
Band5 (2000[Hz])
Band6 (3150[Hz])
Band7 (4000[Hz])
Band8 (8000[Hz])
Q 0.5, 1.0, 2.0, 4.0, 8.0
Simultaneously adjusts the width of the
adjusted ranges for all the frequency bands.
Level # 0–127
Output level
03: ISOLATOR
This is an equalizer which cuts the volume greatly, allowing you to add a special
eect to the sound by cutting the volume in varying ranges.
L in
R in
L out
R out
Isolator
Low Boost
Low Boost
Isolator
Parameter Value Explanation
Boost/Cut Low #
-60–+4[dB]
These boost and cut each of the High, Middle,
and Low frequency ranges.
At -60 dB, the sound becomes inaudible. 0 dB is
equivalent to the input level of the sound.
Boost/Cut Mid #
Boost/Cut High #
Anti Phase Low Sw
OFF, ON
Turns the Anti-Phase function on and o for the
Low frequency ranges.
When turned on, the counter-channel of stereo
sound is inverted and added to the signal.
Anti Phase Low Level
0–127
Adjusts the level settings for the Low frequency
ranges.
Adjusting this level for certain frequencies allows
you to lend emphasis to specic parts (This is
eective only for stereo source.).
Anti Phase Mid Sw
OFF, ON
Settings of the Anti-Phase function for the Middle
frequency ranges.
The parameters are the same as for the Low
frequency ranges.
Anti Phase Mid Level
0–127
Low Boost Sw
OFF, ON
Turns Low Booster on/o.
This emphasizes the bottom to create a heavy
bass sound.
Low Boost Level
0–127
Increasing this value gives you a heavier low end.
* Depending on the Isolator and lter settings
this eect may be hard to distinguish.
Level
0–127
Output level
3
3
3