Roland juno-ds61 - Patch Mode; Pitch Envelope Parameters; Filter Parameters (TVF)

8
Patch Mode
PITCH ENV
Parameter Value/Explanation
Pitch Env Depth
Adjusts the eect of the Pitch Envelope. Higher settings will cause the
pitch envelope to produce greater change. Negative (-) settings will invert
the shape of the envelope.
-12–+12
Pitch Env V-Sens
Keyboard playing dynamics can be used to control the depth of the pitch
envelope. If you want the pitch envelope to have more eect for strongly
played notes, set this parameter to a positive (+) value. If you want the
pitch envelope to have less eect for strongly played notes, set this to a
negative (-) value.
-63–+63
Pitch Env T1
V-Sens
This allows keyboard dynamics to aect the Time 1 of the Pitch envelope.
If you want Time 1 to be speeded up for strongly played notes, set this
parameter to a positive (+) value. If you want it to be slowed down, set this
to a negative (-) value.
-63–+63
Pitch Env T4
V-Sens
Use this parameter when you want key release speed to aect the Time
4 value of the pitch envelope. If you want Time 4 to be speeded up for
quickly released notes, set this parameter to a positive (+) value. If you
want it to be slowed down, set this to a negative (-) value.
-63–+63
Pitch Env Time KF
Use this setting if you want the pitch envelope times (Time 2–Time 4) to
be aected by the keyboard location. Based on the pitch envelope times
for the C4 key, positive (+) settings will cause notes higher than C4 to
have increasingly shorter times, and negative (-) settings will cause them
to have increasingly longer times. Larger settings will produce greater
change.
-100–+100
Time
Key
Pitch Env Time 1–4
Specify the pitch envelope times (Time 1–Time 4).
Higher settings will result in a longer time until the next pitch is reached.
(For example, Time 2 is the time over which the pitch changes from Level 1
to Level 2.)
0–127
Pitch Env Level
0–4
Specify the pitch envelope levels (Level 0–Level 4).
It determines how much the pitch changes from the reference pitch (the
value set with Coarse Tune or Fine Tune on the Pitch screen) at each point.
Positive (+) settings will cause the pitch to be higher than the standard
pitch, and negative (-) settings will cause it to be lower.
-63–+63
Note on
Note o
Time
Pitch
T: Time L: Level
TVF
Parameter Value/Explanation
Filter Type
Selects the type of lter. A lter cuts or boosts a specic frequency region
to change a sound’s brightness, thickness, or other qualities.
* If you set “LPF2” or “LPF3,” the setting for the Resonance (p. 8) will be
ignored .
OFF No lter is used.
LPF
Low Pass Filter. This reduces the volume of all frequencies above
the cuto frequency in order to round o, or un-brighten the
sound. This is the most common lter used in synthesizers.
BPF
Band Pass Filter. This leaves only the frequencies in the region of
the cuto frequency, and cuts the rest. This can be useful when
creating distinctive sounds.
HPF
High Pass Filter. This cuts the frequencies in the region below the
cuto frequency. This is suitable for creating percussive sounds
emphasizing their higher tones.
PKG
Peaking Filter. This emphasizes the frequencies in the region of
the cuto frequency. You can use this to create wah-wah eects
by employing an LFO to change the cuto frequency cyclically.
LPF2
Low Pass Filter 2. Although frequency components above the
cuto frequency are cut, the sensitivity of this lter is half that of
the LPF. This makes it a comparatively warmer low pass lter. This
lter is good for use with simulated instrument sounds such as
the acoustic piano.
LPF3
Low Pass Filter 3. Although frequency components above the
cuto frequency are cut, the sensitivity of this lter changes
according to the cuto frequency. While this lter is also good
for use with simulated acoustic instrument sounds, the nuance
it exhibits diers from that of the LPF2, even with the same TVF
Envelope settings.
Cuto Frequency
Selects the frequency at which the lter begins to have an eect on the
waveform’s frequency components.
“LPF/LPF2/LPF3” selected for the Filter Type
Lower cuto frequency settings reduce a tone’s upper harmonics for a
more rounded, warmer sound. Higher settings make it sound brighter.
“BPF” selected for the Filter Type
Harmonic components will change depending on the TVF Cuto
Frequency setting. This can be useful when creating distinctive sounds.
“HPF” selected for the Filter Type
Higher Cuto Frequency settings will reduce lower harmonics to
emphasize just the brighter components of the sound.
“PKG” selected for the Filter Type
The harmonics to be emphasized will vary depending on Cuto Frequency
setting.
MEMO
To edit the overall patch while preserving the relative dierences in the
Cuto Frequency values set for each tone, set the Cuto Oset (p. 4).
0–127
Resonance
Emphasizes the portion of the sound in the region of the cuto frequency,
adding character to the sound. Excessively high settings can produce
oscillation, causing the sound to distort.
0–127
Cuto Keyfollow
Use this parameter if you want the cuto frequency to change according
to the key that is pressed. Relative to the cuto frequency at the C4 key
(center C), positive (+) settings will cause the cuto frequency to rise
for notes higher than C4, and negative (-) settings will cause the cuto
frequency to fall for notes higher than C4.
Larger settings will produce greater change.
-200–+200
Cuto frequency
(Octave)
Key
2
2
2