Roland RD-2000 User Manual

16
Adding Reverberation to the Sound (REVERB)
Applying reverb adds pleasing reverberation to what you play, so it
sounds almost as if you were playing in a concert hall.
1. Press the ZONE EFFECTS [SELECT] button several times, to select
the “REVERB/DELAY.”
2. Turn the REVERB [TYPE] knob, to select the reverb type.
3. Turn the REVERB [LEVEL], [TIME] and [PRE DELAY] knobs to
adjust the amount of reverb eect to be applied.
MEMO
5 If you use the ZONE EFFECTS [SELECT] button to select “CTRL,” the
[REV SEND] knob can adjust the reverb send level. If this value is
“0,” turning the REVERB [LEVEL]–[PRE DELAY] knobs has no eect.
&
REV (Reverb Send Level) in the zone settings (ZONE EDIT)
5 If you hold down the [SHIFT] button and turn the REVERB
[LEVEL]–[PRE DELAY] knobs, the Reverb screen appears. In the
Reverb screen, you can edit the reverb type and other reverb-
related parameters.
Adding Delay to the Sound (DELAY)
By adding the delay eect, you can give the sound greater dimension,
with more fatness and breadth.
1. Press the ZONE EFFECTS [SELECT] button several times, to select
the “REVERB/DELAY.”
2. Press the [DELAY ON] button to make the indicator light.
The delay eect will turn on/o each time you press the button.
3. Turn the DELAY [TYPE] knob, to select the delay type.
4. Turn the DELAY [LEVEL], [TIME] and [FEEDBACK] knobs to adjust
the character of the delay eect.
MEMO
If you use the ZONE EFFECTS [SELECT] button to select “CTRL,” the
[DLY SEND] knob can adjust the delay send level. If this value is “0,”
turning the DELAY [LEVEL]–[FEEDBACK] knobs has no eect.
&
“DLY (Delay Send Level)” in the zone settings (ZONE EDIT)
Applying an Eect (MODULATION FX)
In the MODULATION FX section you can apply a variety of eects such
as modulation-type eects to zones 1–4.
MEMO
Eects cannot be applied to zones 5–8.
1. Press the [ZONE EFFECTS] button to make the indicator light.
2. In the MODULATION FX section, press the [ON] button to make
the indicator light.
The eect will turn on/o each time you press the button.
3. In the MODULATION FX section, turn the [TYPE] knob to select
the eect type.
For a list of the eects that can be used in modulation FX, refer to
“Parameter Guide (English)” (PDF).
4. In the MODULATION FX section, turn the [DEPTH], [RATE] and
[FEEDBACK] knobs to adjust the eect.
MEMO
For details on the eect parameters, refer to “Parameter Guide
(English)” (PDF). For details on how to obtain the PDF, refer to
“Obtaining PDF Manuals” on the front cover.
* You can assign this to a pedal by setting the Program Edit
“Pedal” parameter. In this case, if the SYSTEM setting “Control
Destination” is set to PROGRAM, you can control the tones
whose zone setting (ZONE EDIT) has a check mark for “MOD FX
(Modulation FX Control Destination).”
Applying Tremolo (TREMOLO)
In the TREMOLO section, you can adjust the rate and depth of the
tremolo eect.
MEMO
Tremolo is applied only to zones 1–4. It does not apply to zones 5–8.
1. Press the [ZONE EFFECTS] button to make the indicator light.
2. In the TREMOLO section, press the [ON] button to make the
indicator light.
The tremolo will turn on/o each time you press the button.
3. In the TREMOLO section, turn the [TYPE] to select the tremolo
waveform.
4. In the TREMOLO section, turn the [DEPTH] and [RATE] knobs to
adjust the tremolo.

Roland RD-2000 Specifications

General

Pedal jack	Yes
Sound effects	Compression, Equalization, Modulation, Reverberation
Tones quantity	1100
Built-in speaker(s)	No
Number of front panel sliders	9
Reverberation effects quantity	6
Preset programs quantity	300
Keyboard name	PHA-50
Keys quantity	88 keys
Display resolution	256 x 80 pixels
Power consumption (max)	23 W
Audio (L/R) out	2
Headphone outputs	1
USB connector type	USB Type-A, USB Type-B
Headphone connectivity	6.3 mm
Product color	Black
Cables included	AC

Weight and Dimensions

Depth	367 mm
Width	1412 mm
Height	140 mm
Weight	21700 g