Roland RD-600 - Page 67

@ Note on
Status 2nd byte 3rd byte
onH kkIi wH
OH-FH (ch.1-ch.16)
O0H-7FH (0-127)
OOH-7FH (0-127)
n= MIDI channel number:
kk = note number:
vv = note an velocity:
* Not transmitted if Tx.Part Switch = OFF.
* Hf you play the key within the range of a Part,the Note On/Off message will be sent
with the MIDI channel set to the Part.
The value figured out with the strength of playing keyboard, velocity sensitivity and
velocity max of the Part is transmitted as “Velocity”.
Each Part allows the transposition to +-36 semitones.
Note message transposed exceeding 0-127 range will be converted to the Note message
of the closest octave that is out of the range.
®@ Control Change
‘) Bank Select (Controller number 0, 32)
Status 2nd byte ard byte
Ro 00H mmit
BnH 20H WH
OH-FH (ch.1-ch.16)
mm, I= Bank number: OOH, 00H-7FH, 7FH (bank. 1-bank.16384)
* Not transmitted if Bank Select parameter or Program Change parameter is OFF (Initial
Value = OFF)
n= MIDI channel number:
2 Modulation (Controller number 1)
Status 2ndbyte 3rd byte
BnH O1H vwH
OH-FH (ch.1-ch.16)
OOH-7FH (0-127)
n= MIDI channel number:
vv = Modulation depth:
* Nat transmitted if Modulation lever Switch = OFF {Initial Value = ON)
* This message is transmitted if Modulation is assigned to FC1 or FC2.
(Not transmitted if FC4,2 Pedal Switch = OFF)
‘D Data Entry (Controller number 6, 38)
Status aodbyte ded. byte
Balt 06H mmH
Bot 20H! WH
n= MIDI channel number: OM-FH (ch.1-ch.16)
mm, Il = the value of the parameter specified by RPN/NRPN
min = MSB, I] = LSB
‘2 Volume (Controller number 7)
Status And byte Ard byte
Built 7H vwH
OH-FH (ch.1-ch.16)
0OH-7FH (0-127)
n= MIDI channel number:
vv = Volume:
> Pan (Controiler number 10)
Status 2ud_byte ard_byte
Bn NAH wH
n= MIDI channel number: OH-FH (ch.1-ch.16)
vv = pan: QOH-40H-7FH (Left-Center-Right)
* This message is transmitted if Pan is assigned to FC] or FC2.
{Not transmitted if FC1,2 Pedal Switch = OFF)
©) Expression (Controller number 11)
Status 2d byte ard byte
Bui OBH yvvH
OH-FH (ch.i-ch.16)
OOH-7FH (0-127)
This message is transmitted if Expression is assigned to FC] or FC2.
{Nat transmitted if FC1,2 Pedal Switch = OFF)
n= MIDI channel number:
vy = Expression:
2 Hold 1 (Controller number 64)
Status. 2nd byte 3rd byte
BoH 40H vH
OH-FH (ch.1-ch.16)
O0H-7FH (0-127)
This message is transmilted if Hold] is assigned to FC1 or FC2.
(Not transmitted if FC1,2 Pedal Switch = OFF)
n= MIDI channel number:
vv = Control value:
© Sostenuto (Controller number 66)
Status 2nd byte ard byte
BnH 42H vvH
OH-FH (ch.1-ch.16)
vv = Control value: 00H-7FH (0-127) 0-63 = OFF, 64-127 = ON
* This message is transmitted if Sostenuto is assigned to FC1 or FC2.
(Nottransmitted if FC1,2 Pedal Switch = OFF)
n= MIDI channel number:
© Soft (Controller number 67)
Status 2ndbyte sd byte
BnH 43H vvH
OH-FH (ch.3-ch.16)
vv = Control value: 00H-7FH (0-127) 0-63 = OFF, 64-127 = ON
This message is transmitted if Soft is assigned to FC] or PC2.
{Nattransmitted if FC1,2 Pedal Switch = OFF)
n = MIDI channel number:
D Effect 1 (Reverb Send Level) (Controller number 91)
BnH 5BH vwH
n= MIDI channel number: OH-FH (ch.1-ch.16}
vv = Control value: 00H-7FH (0-127)
* This message is transmitted if Reverb Amount is assigned to FCT or FC2.
(Nottransmitled if FC1,2 Pedal Switch = OFF)
‘D Effect 3 (Chorus Send Level) (Controller number 93)
Status 2nd byte 3rd byte
BnH 5DH vvH
n = MIDI channel number: OH-FH (ch.1-ch.16)
vv = Control value: O0H-7FH (0-127
* This message is transmitted if Chorus Amount is assigned to FC1 or FC2.
(Nottransmitted if FC1,2 Pedal Switch = OFF)
© NRPN MSB/LSB (Controller number 98, 99)
Status Qndbyie rd byte
BnH 63H mmH
BnH 62H nH
n = MIDI channel number: 0H-FH (ch.1-ch.16)
mm - upper byte of the parameter number specified by NRPN
Ii = lower byte of the parameter number specified by NRPN
On the RD-600, NRPN can be used to modify the following parameters.
NRPN Data entry
MSBRLSB =-MSB
01H 20H mmH.
Descripti
TVF cutott frequency {relative change on specified channel)
mm: OEH+A0H-72H (-50)- 0 - +50)
1H 63H mmH TVF&TVA Env. Attack time (relative change on specified chan-
nel}
mmm: 0OEH-40H-72H (-50-0- +50)
01H 64H mmH TVF&TVA Env. Decay lime (relative change on specified chan-
nel)
mim: OEH~0H-72H (-50 - 0 - +50)
O1H 66H mmH TVF&TVA Env. Release time (relative change an specified
channel)
mm: OEH-40H-72H (-50 - 0 - +50)
67