23
Jan. 2005 RD-700SX
Test Category Details
0. Product Information
Upon entering Test mode, the following screen appears in the LCD display.
fig.13-01test01.eps
The product name and program version information as indicated in the
display; confirm the version number for each category.
The PRG Build No: and Booter Version: are unrelated to Service.
Press [CURSOR →] to advance to the next test.
1. SG Check
A check of the memory and sound module device is begun.
fig.13-02test02.eps
After the above screen is displayed, the procedure automatically
advances to the next test.
The results of the test are indicated in the “89. Device Check” screen.
After this screen is displayed, a reverse task of the device check is performed.
Approximately 2 minutes is required for the entire device check procedure.
2. SW/LED Check 1
An operational check of the switches with LEDs is performed.
fig.13-03test03.eps
The switch to be tested is indicated by the flashing of the switch LED;
press each switch as indicated by the respective switch’s LED.
[V-LINK]:RED → [SOUND CONTROL]:RED → [ON/OFF]:RED →
[REVERB]:REDx3 → [CHORUS/DELAY]:REDx2 → [ON/OFF]:RED →
[LOWER2]:GREEN → [LOWER1]:GREEN → [UPPER2]:RED →
[UPPER1]:RED → [EXTERNAL/INTERNAL]:RED → [RHYTHM]:RED
→ [CONTROL/ZONE LEVEL]:RED → [ARPEGGIO]:RED →
[SPLIT]:RED → [TRANSPOSE]:RED → [EXIT]:RED → [F1]:RED →
[F2]:RED → [ENTER]:RED → [SETUP]:ORANGE → [LOWER]:GREENx2
→ [UPPER]:REDx2 → [A]:RED → [B]:RED → [EDIT]:RED →
[WRITE]:RED → [NUMLOCK]:RED → [PIANO]:RED/GREEN →
[E.PIANO]:RED/GREEN → [CLAV/MALLET]:RED/GREEN →
[ORGAN]:RED/GREEN → [STRINGS]:RED/GREEN → [PAD]:RED/
GREEN → [GUITAR/BASS]:RED/GREEN → [BRASS/WINDS]:RED/
GREEN → [VOICE/SYNTH]:RED/GREEN → [RHY/GM2]:RED/
GREEN
A total of 53 switches are checked.
If “53/53” appears in the display, the procedure automatically advances
to the next test.
3. SW/LED Check 2
fig.13-04test04.eps
An operational check of the switches without LEDs is performed.
[CURSOR ↑] → [CURSOR ←] → [CURSOR →] → [CURSOR ↓] → [DEC]
→ [INC] → [ONE TOUCH PIANO] → [ONE TOUCH E.PIANO]
Test the switches in the following sequence (total of 8 switches).
[CURSOR ↑] → [CURSOR ←] → [CURSOR →] → [CURSOR ↓] → [DEC]
→ [INC] → [ONE TOUCH PIANO] → [ONE TOUCH E.PIANO]
If "8/8" appears in the display, the procedure automatically advances to
the next test.
4. Bender/Pedal Check
A bender and pedal AD check is performed.
fig.13-05test05.eps
Adjust each controller and confirm the changes in the AD value.
The value at the bender’s center position is 64.
Controllers that change in a range of 0 to 127 have highlighted
backgrounds.
After the check of all controllers is completed, the procedure
automatically advances to the next test
5. Volume Check.
An AD check of the panel slider volume and rotary volume controls is
performed.
fig.13-06test06.eps
Adjust each controller and confirm the changes in the AD value.
Slider volume : LOWER2/LOWER1/UPPER2/UPPER1
Rotary Volume : LOW/FREQ/LEVEL/HIGH/DEPTH x2/CONTROL/
CONTRAST
The LOW, LEVEL, AND HIGH volume controls have center clicks.
Confirm that the value is 64 at the center position.
After the check of all controllers is completed, the procedure
automatically advances to the next test.
6. LCD Check
Confirm the LCD display status.
fig.13-07test07.eps
Upon entering this test, the [PIANO], [E.PIANO], and [CLV/MALLET]
LEDs start to flash.
0: Press [PIANO]; all of the LCD pixels turn on (white display).
1: Press [E.PIANO]; all of the LCD pixels turn off (blue display).
2: Press [CLV/MALLET]; a pattern of vertical stripes is display in the
lower half of the LCD.
After all of the test patterns have been displayed, press [CURSOR \>] to
advance to the next test.
DISPLAY MEANING
Product Name: CD00C
PRG Version No: Program version number
PRG Build No: Program build number
Booter Version: Booter Version number
Bender :0-64-127
Moduration :0-127
Damper :0-127
FC1 :0-127
FC2 :0-127
To Next Page
Loading...
