Roland SH-201 - LFO Parameters

62
Parameter list
LFO parameters
Parameter
Value Explanation Panel operation
LFO1
LFO SHAPE
TRI, SIN, SAW, SQR, TRP,
S&H, RANDOM
Selects the LFO 1 waveform. Press the SHAPE buttons
(p. 40)
TEMPO SYNC
Switch
OFF, ON Synchronizes the LFO 1 RATE (modulation speed) to
the tempo of the arpeggiator or recorder.
Press the TEMPO SYNC
button (p. 41)
TEMPO SYNC
NOTE
16, 12, 8, 4, 2, 1, 3/4, 2/3, 1/2,
3/8, 1/3, 1/4, 3/16, 1/6, 1/8,
3/32, 1/12, 1/16, 1/24, 1/32
Specifies the LFO 1 rate (modulation speed) in terms of
a note value.
Press the TEMPO SYNC
button and then turn the
RATE knob (p. 41)
RATE 0–127 Specifies the speed of LFO 1 modulation. Turn the RATE knob (p. 41)
KEY TRIGGER OFF, ON If this is “ON,” LFO 1 will begin a new cycle the mo-
ment you press a key.
Hold down the LFO 1 but-
ton and press the TEMPO
SYNC button
DESTINATION 1 PITCH1, PW1, FILTER,
AUDIO-FIL
Specifies the parameter that will be modulated by LFO
1.
Press the DESTINATION 1
button (p. 42)
DEPTH 1 -63– +63 Specifies the depth of modulation that will be applied
to the parameter you selected for DESTINATION 1.
Turn the DESTINATION 1
DEPTH knob (p. 42)
DESTINATION 2 PITCH2, PW2, AMP Specifies the parameter that will be modulated by LFO
1.
Press the DESTINATION 2
button (p. 43)
DEPTH 2 -63– +63 Specifies the depth of modulation that will be applied
to the parameter you selected for DESTINATION 2.
Turn the DESTINATION 2
DEPTH knob (p. 43)
FADE TIME 0–127 Specifies the time until the maximum LFO 1 amplitude
is reached.
Hold down the LFO 1 but-
ton and turn the RATE knob
LFO2
SHAPE
TRI, SIN, SAW, SQR, TRP,
S&H, RANDOM
Selects the LFO 2 waveform. Press the SHAPE buttons
(p. 40)
TEMPO SYNC
Switch
OFF, ON Synchronizes the LFO 2 RATE (modulation speed) to
the tempo of the arpeggiator or recorder.
Press the TEMPO SYNC
button (p. 41)
TEMPO SYNC
NOTE
16, 12, 8, 4, 2, 1, 3/4, 2/3, 1/2,
3/8, 1/3, 1/4, 3/16, 1/6, 1/8,
3/32, 1/12, 1/16, 1/24, 1/32
Specifies the LFO 2 rate (modulation speed) in terms of
a note value.
Press the TEMPO SYNC
button and then turn the
RATE knob (p. 41)
RATE 0–127 Specifies the speed of LFO 2 modulation. Turn the RATE knob (p. 41)
KEY TRIGGER OFF, ON If this is “ON,” LFO 2 will begin a new cycle the mo-
ment you press a key.
Hold down the LFO 2 but-
ton and press the TEMPO
SYNC button
DESTINATION 1 PITCH1, PW1, FILTER,
AUDIO-FIL
Specifies the parameter that will be modulated by LFO
2.
Press the DESTINATION 1
button (p. 42)
DEPTH 1 -63– +63 Specifies the depth of modulation that will be applied
to the parameter you selected for DESTINATION 1.
Turn the DESTINATION 1
DEPTH knob (p. 42)
DESTINATION 2 PITCH2, PW2, AMP Specifies the parameter that will be modulated by LFO
2.
Press the DESTINATION 2
button (p. 43)
DEPTH 2 -63– +63 Specifies the depth of modulation that will be applied
to the parameter you selected for DESTINATION 2.
Turn the DESTINATION 2
DEPTH knob (p. 43)
FADE TIME 0–127 Specifies the time until the maximum LFO 2 amplitude
is reached.
Hold down the LFO 2 but-
ton and turn the RATE knob
FADE TIME
DEPTH
time
Key-on
SH-201_r_e.book 62 ページ ２００６年４月２７日 木曜日 午前１１時２８分