REVERB MACRO is a parameter used to select the preset type of the effect.
When set to another REVERB MACRO, all other reverb parameters will reset to the values set for each type of REVERB MACRO.
40 01 38 00 00 01 00 - 07 CHORUS MACRO 00: Chorus 1 02 Chorus 3
01: Chorus 2
02: Chorus 3
03: Chorus 4
04: Feedback Chorus
05: Flanger
06: Short Delay
07: Short Delay(FB)
40 01 39 00 00 01 00 - 07 CHORUS PRE-LPF 0-7 00 0
40 01 3A 00 00 01 00 - 7F CHORUS LEVEL 0-127 40 64
40 01 3B 00 00 01 00 - 7F CHORUS FEEDBACK 0-127 08 8
40 01 3C 00 00 01 00 - 7F CHORUS DELAY 0-127 50 80
40 01 3D 00 00 01 00 - 7F CHORUS RATE 0-127 03 3
40 01 3E 00 00 01 00 - 7F CHORUS DEPTH 0-127 13 19
40 01 3F 00 00 01 00 - 7F CHORUS SEND LEVEL TO REVERB 0-127 00 0
CHORUS MACRO is a parameter used to select the preset type of effect.
When set to another CHORUS MACRO, then all other chorus parameters will reset to the values set for each type of CHORUS MACRO.
40 1x 00 00 00 02 00 - 7F TONE NUMBER CC#00 VALUE (0-127) 00 0
40 1x 01# 00 - 7F P.C. VALUE (1-128) 00 1
40 1x 02 00 00 01 00 - 10 Rx. CHANNEL 1 - 16,OFF Same as the Part#
40 1x 03 00 00 01 00 - 01 Rx. PITCH BEND OFF / ON 01 ON
40 1x 04 00 00 01 00 - 01 Rx. CH PRESSURE(CAf) OFF / ON 01 ON
40 1x 05 00 00 01 00 - 01 Rx. PROGRAM CHANGE OFF / ON 01 ON
40 1x 06 00 00 01 00 - 01 Rx. CONTROL CHANGE OFF / ON 01 ON
40 1x 07 00 00 01 00 - 01 Rx. POLY PRESSURE(PAf) OFF / ON 01 ON
40 1x 08 00 00 01 00 - 01 Rx. NOTE MESSAGE OFF / ON 01 ON
40 1x 09 00 00 01 00 - 01 Rx. RPN OFF / ON 01 ON
40 1x 0A 00 00 01 00 - 01 Rx. NRPN OFF / ON 00 (01*) OFF (ON*)
* Rx. NRPN is set to OFF by power-on reset or by "General MIDI mode On", and it is set to ON by "GS RESET" .
40 1x 0B 00 00 01 00 - 01 Rx. MODULATION OFF / ON 01 ON
40 1x 0C 00 00 01 00 - 01 Rx. VOLUME OFF / ON 01 ON
40 1x 0D 00 00 01 00 - 01 Rx. PANPOT OFF / ON 01 ON
40 1x 0E 00 00 01 00 - 01 Rx. EXPRESSION OFF / ON 01 ON
40 1x 0F 00 00 01 00 - 01 Rx. HOLD1 OFF / ON 01 ON
40 1x 10 00 00 01 00 - 01 Rx. PORTAMENTO OFF / ON 01 ON
40 1x 11 00 00 01 00 - 01 Rx. SOSTENUTO OFF / ON 01 ON
40 1x 12 00 00 01 00 - 01 Rx. SOFT OFF / ON 01 ON
40 1x 13 00 00 01 00 - 01 MONO/POLY MODE Mono / Poly 01 Poly
(=Bn 7E 01 / Bn 7F 00)
40 1x 14 00 00 01 00 - 02 ASSIGN MODE 0 = SINGLE 00 at x=0 SINGLE
1 =LIMITED-MULTI 01 at x≠0 LIMITED-MULTI
2 = FULL-MULTI
ASSIGN MODE is a parameter used to select the voice assign manner when "multiple Note Ons" occur(the same note number on the same channel at
the same time).
The best assign modes ( SINGLE(0) for Drum part and LIMITED-MULTI(1) for the other parts ) are selected automatically, so you need not reset this
parameter.
40 1x 15 00 00 01 00 - 02 USE FOR RHYTHM PART 0 = OFF 00 at x≠0OFF
1 = MAP1 01 at x=0 MAP1
2 = MAP2
USE FOR RHYTHM PART is a parameter to define the part to be used as an ordinary part (0), as a drum part using DRUM MAP1(1), or a drum part
using DRUM MAP2(2). The default is MAP1(1) for Part10 (MIDI CH=10, x=0), and all other parts are set to ordinary parts (OFF(0)).
40 1x 16 00 00 01 28 - 58 PITCH KEY SHIFT -24 - +24 40 0 [semitones]
[semitones]
40 1x 17 00 00 02 08 - F8 PITCH OFFSET FINE -12.0 - +12.0 [Hz] 08 00 0 [Hz]
40 1x 18# Use nibblized data.
40 1x 19 00 00 01 00 - 7F PART LEVEL 0 - 127 64 100
(=Bn 07 vv)
40 1x 1A 00 00 01 00 - 7F VELOCITY SENSE DEPTH 0 - 127 40 64
40 1x 1B 00 00 01 00 - 7F VELOCITY SENSE OFFSET 0 - 127 40 64
40 1x 1C 00 00 01 00 - 7F PART PANPOT Random,
-63(LEFT) - +63(RIGHT) 40 0 (center)
(=Bn 0A vv, except random)
40 1x 1D 00 00 01 00 - 7F KEY RANGE LOW C-1 - G9 00 C-1
40 1x 1E 00 00 01 00 - 7F KEY RANGE HIGH C-1 - G9 7F G9
40 1x 1F 00 00 01 00 - 5F CC1 CONTROLLER NUMBER 0 - 95 10 16
40 1x 20 00 00 01 00 - 5F CC2 CONTROLLER NUMBER 0 - 95 11 17
49
To Next Page
Loading...
