Why does 'Found New Hardware Wizard' appear again after Roland driver was installed (Windows XP)?
If the 'Found New Hardware Wizard' appears again after the driver for your Roland Media Converter has been installed on Windows XP, it might be because the UM-ONE is connected to a different USB connector than the one used during the initial driver installation. To fix this, follow step 9 of the driver installation procedure and install the driver.
Why can't I play back or record with my Roland UM-ONE Media Converter?
There could be several reasons why you cannot play back or record with the Roland Media Converter. Here are a few things to check: * Ensure the driver is installed. * Verify that the software’s input and output device are configured correctly, selecting the UM-ONE as both. * Make sure the UM-ONE is properly connected to the computer and that the USB indicator is on. * Check that the MIDI IN and MIDI OUT cables are correctly connected. * Confirm the settings of the sound module. Also, avoid disconnecting and reconnecting the USB cable while using the UM-ONE, and ensure the UM-ONE is connected after the computer has fully started. Finally, remember that MIDI devices cannot be selected in Media Player, so use different software.
Why is the sound interrupted during playback or are sounds missing on my Roland UM-ONE Media Converter?
If the sound is interrupted during playback or sounds are missing when using the Roland Media Converter, consider the following: * Close any programs that are not currently in use. * Ensure your system software is up to date by running Windows Update, Microsoft Update, or Mac OS X Software Update. * Update the drivers for your computer’s internal chipset, graphics card, and LAN hardware. * Connect the UM-ONE directly to one of the computer’s USB connectors instead of using a USB hub. Also, configure power management settings and consider enabling the [Lighten Load] setting in the driver (Windows). Finally, avoid trying to play back or record immediately after the computer starts up or wakes up from sleep mode.
What to do if I cannot install Roland UM-ONE?
If you're having trouble installing the Roland Media Converter, consider these potential causes: * Ensure you are logged in with a user account that has administrator privileges. * If you're using Windows XP, check the 'Driver Signing Options' setting. * Make sure to exit all other programs, including resident programs like antivirus software, before starting the installation.
What to do if I cannot select or use the Roland UM-ONE device?
If you cannot select or use the UM-ONE device with your Roland Media Converter, try the following: * Verify that the driver is installed. * Ensure the UM-ONE’s USB indicator is lit, indicating a proper connection. * If the device name is displayed, exit all programs using the UM-ONE, disconnect and reconnect the USB cable. * If your computer entered standby, hibernate, or sleep mode while the UM-ONE was connected, exit all programs, disconnect and reconnect the USB cable, or restart the computer. Also, connect the UM-ONE after the computer has started up. Note that MIDI devices cannot be selected in Media Player, so use different software.
What to do if Roland UM-ONE Media Converter installer does not exit?
If the installer for the Roland Media Converter does not exit, check the following: * Ensure the computer is connected to a power cord and not running on battery power. * Disconnect any USB devices other than a mouse and keyboard during installation. * If using a USB hub, make sure it connects to a power supply.
What to do if a warning or error appears during Roland UM-ONE Media Converter installation on Windows?
If a warning or error appears during the installation of the Roland Media Converter on Windows, check the 'Device Manager' for any devices listed as 'Other device,' 'Unknown device,' or devices with a '?', '!', or 'x' displayed. If you find any of these, reinstall the UM-ONE driver.
Why does a numeral such as '2-' appear at the beginning of Roland device name in Windows?
If a numeral, such as '2-', appears at the beginning of the device name for your Roland Media Converter in Windows, it may be because the UM-ONE is connected to a different USB connector than the one used during driver installation. To resolve this, connect the UM-ONE to the same USB connector used during installation, or reinstall the driver.
Why do duplicate notes sound with my Roland Media Converter?
If you are hearing duplicate notes with your Roland Media Converter, check if the sound module is set to Local On and if the software’s THRU function is turned on. Configure the sound module to Local Off and the software’s THRU function to Off. Consult the owner’s manual for your equipment for specific instructions.
Explains the meaning of warning and caution notices used in the manual.
Explains the meaning of the warning symbols used in the manual.
Guidelines for placing the unit to avoid damage from temperature and humidity.
Instructions for cleaning and maintaining the unit to prevent damage.
Advice on careful handling of jacks, connectors, and transportation.
Precautions for handling discs to ensure proper reading.
Step-by-step guide for installing the UM-ONE driver on Windows OS.
Step-by-step guide for installing the UM-ONE driver on Mac OS X.
Important points to note before using the UM-ONE with software.
How to connect and set up for recording MIDI data or playing a software sound module.
How to send recorded MIDI data to a sound module or play back data.
Solutions for common issues encountered during driver installation.
Tips for resolving issues when the UM-ONE device is not recognized or usable.
Troubleshooting steps for problems with playing back or recording MIDI data.
Adjusting computer settings like driver signing and power management to avoid problems.
Procedures for uninstalling and reinstalling the UM-ONE driver.
How to lighten the MIDI load on Windows for better performance.
General| Type | USB MIDI Interface |
|---|---|
| Ports | 1 MIDI input, 1 MIDI output |
| Connectivity | USB |
| Compatibility | Windows, macOS |
| Included Items | Owner's Manual |
| Power | Bus-powered via USB |
| Data Indicators | LED indicators for MIDI In/Out activity |
| Connectors | MIDI In, MIDI Out, USB |
To Next Page
