Roland XP-10 - Page 81

Chapter 12. Appendix
SEE ea EI LE LR TEL NTE ED EET ESET TR NIT TE TT ETRE SE TC ESTE ASE OS RE ERE A,
@ All Notes Off = (Controller number 123)
Boni 7BH OOH
nh=MUDI channel number : OH - FH (ch.] - ch.36)
* When All Notes Off is rewived, all nates on the corresponding channel will be turned off. However if
Hold 1 or Sastenuto is ON, the sound wil} be continued until these are tummed off.
@ OMNI OFF {Controller number 124)
Status 2ad byte ard byte
Bntl 7CH OH
n=MIDI channel number 20H - FH (ch.} - ch.16)
* The samy processing will be carried out as when All Notes Off is received.
@ OMNI ON {Controller number 125)
Slatus 2nd byte 3rd byte
BnH 7DH OOH
n=MIDI channel number 20H - FH (ch.1 -ch.16)
* OMNI ON is only recognized as “All notes off"; the Mode doesn’t change (OMNI OFF remains).
@ MONO (Controller number 126)
Status 2nd byte 3rd byte
BnH 7EH mmH
: OH - FH (ch.} - ch.36)
OOH - 10H (0-16)
n=MIDI channel number
mme=mono number
* The same processing will be carried out as when Al] Sounds Off and All Notes Off is received, and the cor-
responding channel will be set to Mode 4 (M=1) regardless of the value of “mono number’.
@ POLY {Controller number 127)
Stalus 2nd byte Sid byte
BaH 7FH OOH
n=MIDI channel number 0H - FH (ch.} - ch.16)
* The same processing, will be carried out as when All Sounds Off and All Notes Off is received, and the cor-
responding channel will be set to Mode 3
@ System Realtime Message
@ Timing Clock
Status
FBH
* Received when Sync Source is MIDI.When received Timing Clock,Arpeggio will played with tempo of
intervals of this message.
@ Start
Status
FAH
* Received when Sync Source is MIDI. When received this message, Arpeggio will be started from the first.
®@ Continue
Status
FBH
* Received when Sync Source is MIDLIf received this message when stopped Arpeggio by received
“Stop” Arpeggio will be started from continued from the stopped position.
@ Stop
Status
FCH
* Received when Sync Source is MIDLWhen received this message, Arpeggio will be stopped.
@ Active Sensing
Status
FEH
* When Active Sensing is received, the unit will begin monitoring the intervals of all further messages.
While monitoring, if the interval between messages exceeds 420 ms, the same processing will be carried out
as when All Sounds OH, All Notes Off and Reset All Controllers are received, and message interval monitor-
ing will be halted.
l@ System Exclusive Message
‘Status Data byte Slatus
POH itH, dd, .......c0H F7H
FoH : System Exclusive Message status
: an ID number {manufacturer 1D) to indicate the manufacturer whose Exclusive
message this is. Roland's manufacturer [D is 41H.
TD numbers 7EML and 7FH are extensions of the MIDI standard; Universal Non-
realtime Messages (7EH) and Universal Realtime Messages (7FH).
dd,....ee = data : OOH - 7FH (0 - 127)
F7H : EOX (End Of Exclusive) _
it = 1D number
The System Exclusive Messages received by the XP-111 are; messages related to mode settings, Universal
Realtime System Exclusive messages, Data Requests (RQI), and Data Set (DTD).
@ System exclusive messages related to mode settings
These messages are used to initialize a device to G5 or General MID! mode. When creating performance
data, a “Tum General MIDI System On” message should be inserted at the beginning of a General MIDI
score, and a "GS Reset” message at the beginning of a CS music data. Each song should contain only one
mode message as appropriate fur the type of data. (Do not insert two or more mode setting messages in a
single song.)
“Turn General MIDI System On" and “Turn General MIDI System Off" use Universal Non-realtime Message
format."GS Reset” and "Exit GS mode use Roland system exclusive format “Data Set 1 (DT1)".
© Turn General MIDI System On
This is a command message that resets the internal settings of the unit to the General MIDI initial stale
(General MIDI System - Level 1). After receiving this message, (Model Name $35) will automatically be set
to the proper condition for correctly playing a General MIDI score.
Status Data byty Status
bits] 7EH, 7FH, 09H, 0TH F7H
Byte Explanation
FOH Exclusive status.
7EH 1D number (Dniversal Non-realtime Message}
7FR Device ID (Broadcast)
05H Sub MDA {General MIDI Message)
O1H, Sub 1D#2 {General MIDI On)
F7H EOX {End Of Exclusive}
* When this message is received, Rx.BANK SELECT will be OFF and Rx.NRPN will be OFF,
* This message will not be received if "Rx.GS Reset SW = OFF, or "Rx.Sys.Ex.SW = OFF.
* There must be an interval of at least 50 ms between this message and the next message.
Turn General MIDI System Off
This is a command message thal resets the internal settings of the unit from General MIDI mode to state of
tured on the power.
Status Data byte alus
FOH 7EH, 7FH, 09H, 02H F7H
FOH Exclusive status.
7EH ID number {Universal Non-realtime Message)
7FH Device 1D (Broadcast)
09H snb-[D#t {General MIDI message)
02H sub-[D#2 (General MIDI Off)
F7H EOX (End of exclusive}
* This message will not be received if "Rx.GS Reset SW = OFF,or “Rx Sys.Ex.SW = OFF.
* There must be an interval of at least 50 ms between this message and the next.
O GS reset
GS Reset is a command message that resets the inlernal settings of a device in the GS initial state. This mes-
sage will appear at the beginning of GS music data, and a GS device that receives this message will automat-
ically be sct to the proper slate to correctly playback GS music data.
Stanus
Data
byie
Status
FOH
43H,
dev,
42H,
12H,
40H,
00H,
7FH.
OOH,
41H
F7H
Byte
Explanation
FOH Exclusive status
aH TD number {Roland)
dev Device ID {dev: 00H - 1FH (3 - 32) Initial value is 101107)
2H Model ID (GS)
12H Command ID (DT!)
40H Address MSB
OH Address,
7FH Address LSB
00H Data (GS reset)
4H Checksum
F7H EOX (End Of Exclusive)
* When this message is received, Rx.NRPN will be ON.
* This message will not be received if "Rx.GS Reset SW = OFF, or “Rx.Sys.Ex.SW = OFF,
* There must be an interval of at Jeast 50 ms between this message and the next.
© Exit GS mode
This is a command message that resets the internal settings of the unit from GS mode to state of turned on
the power,
Status Data byte Status
FOH 41H, dev, 42H, 12H, 40H, 00H, 7FH, 7FH, 42H F7H
Byte Explanation
RWW Exclusive status
41H TD number (Roland)
dev Device ID (dev: OOH-1FH (1-32) Initial value is 10H (17))
42H Mode! ID (Gs)
12H Command ID (DTI)
40H Address MSB
OOH 2
7FH Address LSB
7FH Data (Exit GS mode)
2H Checksum
F7H EOX (End of exctusive)
* This message wili not be received if “Rx.GS Reset SW = OFF,or “Rx Sys.Bx.SW = OFF won'l recognize this
message.
* There must be an interval af at least 50 ms between this message and the next.
81