Roland XP-10 - Page 82

Chapter 12. Appendix
@ Universal Realtime System Exclusive Messages
© Master volume
Status Data byte Status
POU 7FH, 7FH, 04H, O1H, UH, mmH 7H
Byle Explanation
FOH Exclusive status
TPH ID number {universal realtime message)
7FH Device ID (Broadcast)
04H Sub 1081 {Device Control messages}
1H Sub ID#2 (Master Volume)
UH Master volume lower byte
momH Master volume upper byte
F7H EOX (End Of Exclusive)
* The lower byte (1H) of Master Volume will be handled as OOH.
* This message will not be received if "Rx.GS Reset SW = OFF, or “Rx Sys.Ex.SW = OFF.
@ Universal Non-realtime System Exclusive Messages
D Inquiry Request
Status Data byte Status
POH, TEN, dev, 06H, OLH F7H
Byte Explanation
FOH Exclusive status
7FH ID number {universal non-realtime message}
dev Device ID (dev: OOH - 1FH Initial value is 10H(17))
O6H,O1H Inquiry Request
F7H EOX {End Of Exclusive)
+ When Inquiry Request is received Inquiry Reply message will be transmitted.
* Regarding the Inquiry Reply, please refer to page 84.
* Even if Device [D is 7FH(Broadcast),inquiry Reply message will be transmitted.
© Data transmission
XP-10 can transmit and receive the various parameters using System Exclusive messages.
The exclusive awssage of GS Format data has a mode! ID of 42H and a device JD of 11H (18), and it is com-
man to all the GS devices,
Request datal RQ?
This message requests the other device to send data. The Address and Size determine the type and amount
of data tu be sent.
When a Data Request message is received, if the device is ready to transmit data and if the address and size
are appropriate, the requested data will be transmitted as a “Data Set 1 (DT1)” message. If not, nothing will
be transmitted,
Status Data byte Statue
FOH 41H, dev, 42H, 11H, aaH, bbH, ccH, ssH, ttH, uH, sum F7H
Byte Explanation
POH Exclusive status
aH {2 number {Roland}
dev Device ID (dev: 00H -1FH — Initial value is 10H(17))
mod Model 1D (mod: GS242H, XP-10=7BH)
1H Command ID (RQ1)
aaH Address MSB_: upper byte of the starting address of the requested data
bbH Address i middle byte of the starting address of the requested data
ect Address LSB: lower byte of the starting adress of the requested data
ssH Size MSB
tH Size
uuH Size LSB
sum Checksum
FH EOX (End Of Exclusive)
* The amount of data that can be transmitted at once time will depend on the type of data, and data must be
requested using a specific starting address and size. Refer to the Address and Size listed in Section 3 (Page
84).
* Regarding the checksum please refer to Section 4 (Page 91).
(2 Data set 1 DT1
‘This is the message that actually performs data transmission, and is used when you wish to transmit the
data.
Stat Data byte Status
AOR 41H, dev, 42H, 12H, aaHt, bbH, ccH, ddH, ... eeH, sum F7H
Byte Explanation
POH Exclusive status
41H 4D number (Roland)
dev Device ID (dev: OOH - 1FH Initial value is 10H(17))
mod Model ID (mod: GS=42H, XP-10=7BH)
RH Command 1D (DT1)
aaH Address MSB_: upper byte of the starting address of the transmitted data
bbli Address : middle byte of the starting address of the transmitted data
ccH Address LSB: lower byte of the starting address of the transmitted data
ddH Data : the actual data to be transmitted. Multiple bytes of data are transmitted
starting from the address.
eH Data
sum Checksum
F7H EOX (End Of Exclusive}
* The amount of data that can be transmitted at one time depends on the type af data, and data can be
received only from the specified starting address and size. Refer to the Address and Size given in Section 3
(Pageé4).
* Data larger than 128 bytes must be divided inte packets of 128 bytes or less. If "Data Set 1” is transmitted
successively, there must be an interval of at least 40 ms between packets.
* Regarding the checksurn please refer to section 4 (Page 91).
82
Section 2. Transmit dota
@ Channel Voice Messages
The message is (ransmitled through the Ta Channel set in the MIDI Function. When set to PART transmis-
sion takes place on the MIDI receive channel set for the currently Part.
@ Note off
Status dod byte 3ed byte
8nH kkH vwH
n=MIDI channel number 20H - FH (ch. - ch 16)
kk=note number 2 OOH - 7FH (0 - 127}
vvenote off velocity : 00H - 7FH (0 - 127)
@ Note on
Status nu byte 3rd byte
on kkH vwH
n=MIDI channel number
kksnote number
vv=note on velocity
: OH - FH (ch E - ch.16)
00H - 7FH (0 - 127)
:O1H - 7FH (1 - 127)
@ Control Change
* By selecting a Control Change Number that corresponds to the selting of the System Setup Slider]
CC#/Slider2 CC#/Pedal CC#, you can transmit any desired contral change. The settings will be transmit on
the transmit channel of current part.
© Bank Select (Controller number 0,32)
Status 2nd byte Sard byte
BaH OOH mmH
BnH 2H uH
n=MIDI channel number > OH - FH (ch.t - ch.16}
mm,ji=Bank number :00H,00H - 7FH,7FH (bank.! - bank.16384) Initial Value = 00 OOH (bank.1)
* This message is transmitted when tone change is made on the panel or “Send GS Sctup"is executed.
O Modulation ({Controfler number 1)
Status Zod byte rd_byte
BnH. OlH vwH
n=MIDI channel number
vv=Modulation depth
20H - FH (ch.1 - ch.16)
OOH - 7FH (0 - 127)
* This message is transmitted when the Modulation Lever is used.
© Portamento Time (Controller number 5)
Status 2nd byte Sed byte
BnH 05H vvH
n=MIDI channel number
vv=Portamento Time
OH - FH (ch.} - ch.16)
OOH - 7FH (0 - 127) initial vatue = OOH (OFF)
* The current setting value is transmitted when the Portamento Time set to 1 - 127.
© Data Entry (Controller number 6,38)
Status 2nd byte Udbyte
BoH 06H mmH
Bn 2611 ta
n=MIDI channel number 1 OH - FH (ch.} - ch.16)
mm, lJ= the value of the parameter specified by RPN/NRPN
* This message is transmitted when tone change is made on the panel or "Send GS/General MIDI Setup” is
executed,
O Volume (Controiler number 7)
Status dnd byte 3rd byte
Bak 07H vvwH
n=MIDI channel number < OH - FH (ch.1 - ch.i6)
vv=Volume : OOH - 7FH (0 - 127) Initial value= 64H (100)
* This message is transmitted when “Send GS/General MIDI Setup” is executed,
O Pan (Controtler number 10)
Status 2nd. byte ded byte
Bn OAH vwH
n=MIDI channel number 0H - FH (ch.1 - ch.16)
vv=pan : OOH - 40H - 7FH (Lett - Center - Right) Initial value = 40H (Center)
* This message is transmitted when “Send GS/General MIDI Setup” is executed.
O Expression (Controller number 11)
‘Status
BaH OBH wi
n=MIDI channel number 2 OH - FH (ch.1 - ch. 16)
vv=Expression 1 OOH - 7FH (0 - 127} Initial value = 7FH (127)
* This message is transmitted when the pedal in operated with PEDAL Asgn sel to EXPRESSION.
QD Haidt (Controtler number 64)
Stafus 2odbyte acd byte
BrH 40H wH
n=MIDI channel number
vv=Control value
20H - FH {ch.1 - ch.16)
00H - 7FH {0 - 127) 0-63=OFF 64-127=ON
* This message is transmitted when the pedal in operated with PEDAL Asgn set to HOLD.