Ryobi TS1346 User Manual

OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
10 in. COMPOUND
MITER SAW WITH LED
SCIE À ONGLETS COMBINÉS DE
254 mm (10 po) AVEC DEL
SIERRA INGLETEADORA
COMPUESTA DE 254 mm
(10 pulg.) CON GUÍA LED
TS1346/TS1346T
WARNING: To reduce the
risk of injury, the user must read and
understand the operator’s manual
before using this product.
SAVE THIS MANUAL FOR
FUTURE REFERENCE
ADVERTENCIA: Para reducir
el riesgo de lesiones, el usuario debe leer
y comprender el manual del operador
antes de usar este producto.
AVERTISSEMENT : Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation avant
d’employer ce produit.
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
TABLE OF CONTENTS
****************
 General Safety Rules .......................2-3
 Miter Saw Safety Rules ...................3-4
 Additional Safety Rules ...................4-5
 Symbols ..............................................6
 Electrical ............................................. 7
 Glossary of Terms ...............................8
 Features .........................................9-11
 Tools Needed ...................................12
 Loose Parts List ................................12
 Assembly .....................................13-19
 Operation .....................................20-27
 Adjustments .....................................28
 Maintenance ................................29-30
 Parts Ordering / Service ..... Back Page
TABLE DES MATIÈRES
****************
 Règles de sécurité générales ..........2-3
 Règles de sécurité scie à onglets ....3-4
 Règles de sécurité supplémentaires ...4-5
 Symboles ............................................6
 Caractéristiques électriques ...............7
 Glossaire .............................................8
 Caractéristiques ............................9-11
 Outils nécessaires ............................12
 Liste des pièces détachées ..............12
 Assemblage .................................13-19
 Utilisation .....................................20-27
 Réglages ...........................................28
 Entretien ......................................29-30
 Commande de pièces /
réparation ..........................Page arrière
ÍNDICE DE CONTENIDO
****************
 Reglas de seguridad generales .......2-3
 Reglas de seguridad sierra
ingleteadora ....................................3-4
Advertencias de seguridad
adicionales ......................................4-5
 Símbolos ............................................6
 Aspectos eléctricos ............................ 7
 Glosario de términos ..........................8
 Características ..............................9-11
 Herramientas necesarias ..................12
 Lista de piezas sueltas .....................12
 Armado ........................................13-19
 Funcionamiento ...........................20-27
 Ajustes ..............................................28
 Mantenimiento .............................29-30
 Pedidos de piezas /
servicio .......................... Pág. posterior

Ryobi TS1346 Specifications

General

Type	Table Saw
Blade Diameter	10 inches
Motor	15 Amp
Arbor Size	5/8 inches
Max. Cut Depth @ 90 Degrees	3-1/8 inches
Max. Cut Depth @ 45 Degrees	2-1/4 inches

Summary

General Safety Rules

Work Area Safety

Keep clean, well lit, avoid hazards.

Electrical Safety

Proper plugs, grounding, wet conditions.

Personal Safety

Stay alert, use PPE, prevent accidental start.

Power Tool Use and Care

Do not force, check switch, disconnect for adjustments.

Miter Saw Specific Safety Rules

Additional Safety Rules

Extension cords, inspect cords, polarized plugs, know your tool.

Safe Operation Practices

Keep guards, clamp tool, check setups, avoid awkward positions.

Symbols

Signal Words and Meanings

DANGER, WARNING, CAUTION, NOTICE definitions.

Tool Symbols and Explanations

Safety Alert, Read Manual, Eye Protection, etc.

Electrical Information

Double Insulation

Protection from shock without grounding.

Electrical Connection

Power requirements (120V AC, 60 Hz).

Extension Cords

Proper selection and use for safety.

Glossary of Terms

Key Saw Terminology

Definitions of common miter saw terms.

Features

Product Specifications

Blade size, speed, input, and cutting capacity.

Control Panel and Key Components

Identification of controls, guards, fences, and scales.

Key Saw Features

Blade, handles, brakes, lighting, fences, lock mechanisms.

Additional Features

Sliding fence, positive stops, spindle lock, switch trigger.

Tools Needed

Tools Needed for Setup

Tools required for adjustments and blade installation.

Loose Parts

Included Accessories

List of accessories provided with the tool.

Assembly

Unpacking and Initial Inspection

Lifting, checking parts, releasing saw arm.

Assembly Safety Precautions

Warnings before connecting power or modifying.

Assembly Procedures

Mounting and Securing the Saw

Securing to a workbench or stand.

Installing Accessories and Locks

Miter lock handle, dust bag, locking arm.

Blade and Work Clamp Assembly

Blade Wrench and Work Clamp

Description and use of included tools.

Blade Installation and Replacement

Safety and procedure for changing the blade.

Blade Installation Procedure

Detailed Blade Installation Steps

Step-by-step guide for blade mounting.

Squaring the Saw Blade

Squaring Blade to Fence

Aligning blade to fence using a square.

Fence Alignment Adjustments

Adjusting fence and scale indicators.

Squaring Blade to Miter Table

Table Alignment Adjustments

Adjusting positive stops and scale indicators.

Operation

Applications and General Safety

Designed uses, warnings for attachments and operation.

LED Lighting System Usage

Using the LED for cut accuracy.

Cutting Procedures

Miter and Cross Cutting

Setting angles and performing cuts.

Supporting Workpieces During Cuts

Using roller stands for long pieces.

Bevel and Compound Cutting

Bevel Cutting

Setting bevel angle and performing cuts.

Compound Miter Cutting

Combining miter and bevel angles, test cuts.

Special Cutting Techniques

Cutting Compound Miters Chart

Table for angle settings for various cuts.

Crown Molding Cutting

Specific techniques for crown molding.

Cutting Warped and Wide Workpieces

Proper positioning and clamping methods.

Adjustments

Positive Stop and Scale Adjustments

Aligning blade and resetting indicators.

Maintenance

General Maintenance and Cleaning

Cleaning plastic parts, avoiding chemicals.

Brush Replacement

Checking and replacing motor brushes.

LED Lens Cleaning

Cleaning the LED Lens

Maintaining the LED lighting system.

Service and Support

Obtaining Service and Technical Support

Contacting support for parts and repairs.