To Next PageTo Next Page
Need help?Do you have a question about the Safran morphoaccess sigma lite and is the answer not in the manual?
Processes access requests via biometric, card, or PIN, checking access rights.
Terminal interfaces with Access Controllers via TCP/IP, Wiegand, etc., sending user ID for validation.
Terminal sends messages to activate alarms for detected malicious activities like tampering.
Access Controller commands the door latch activation upon granted access via dry contact.
Advise against extreme temperatures and electrostatic discharge risks from synthetic carpeting.
Prohibits installation near flammable or combustible gases/materials due to lack of intrinsic safety.
Avoid exposure of the biometric sensor to blinking lights, sunlight, or UV lights for optimal performance.
Emphasizes careful connection of Ethernet wires to avoid impacting signal sensibility.
Explains the support for the Clock & Data protocol on the Wiegand port and its wiring.
Provides a wiring diagram for Single Door Access Control using a push button.
A network connection is essential for initial terminal configuration, maintenance, and database management.
Details point-to-point Ethernet and LAN connections, covering static IP, DHCP, and tool usage.
Guidelines for setting static IP addresses and network masks when no DHCP server is present.
Instructions on configuring network parameters via MorphoBioToolBox and USB drive for terminal setup.
MorphoAccess SIGMA Lite Series terminals are fully compatible with MorphoManager application (version 8.0.3+).
Compatibility with MEMS (version 7.3.1+) and limitations in Morpho Legacy mode.
Compatibility with SecureAdmin (version v4.1.20.0.1+) and limitations in L1 Legacy mode.
Details the biometric sensor's region of interest and recommends specific fingers for optimal capture.
Provides solutions for common issues like dark or light fingerprint images and general capture advice.
Ensures correct finger height and alignment with the sensor for optimal capture.
Guides on maintaining the correct finger angle, parallel to the sensor, for accurate readings.
Details on avoiding bending or leaving the finger in the air for proper fingerprint capture.
Ensures the finger remains parallel to the sensor surface, avoiding rolling for accurate results.
Instructions on correctly positioning the RF card in front of the contactless card reader.
Details how users input their PIN code using the optional LCD touch screen keypad.
Manufacturer is not liable for issues arising from non-compliance with recommendations or incorrect terminal use.
Advise against self-repair and using unapproved accessories to maintain warranty and prevent damage.
Strongly recommends regular database backups for terminals operating in standalone mode.
Recommends regular synchronization for high time precision applications and notes typical clock deviation.
Specifies using a dry cloth for cleaning, especially the sensor, and prohibits acid, alcohol, or abrasive materials.
Provides physical mounting, electrical interfaces, and connection procedures for the terminal.
Covers terminal overview, configuration, functions, and detailed parameters for administration.
Details host system interface specifications and remote message formats for developers.
Documents new features, known issues, limitations, and recommendations for firmware updates.
Provides contact details for technical support and hotlines across various global regions.
Directs users to websites for the latest firmware, software, and document releases.
Processes access requests via biometric, card, or PIN, checking access rights.
Terminal interfaces with Access Controllers via TCP/IP, Wiegand, etc., sending user ID for validation.
Terminal sends messages to activate alarms for detected malicious activities like tampering.
Access Controller commands the door latch activation upon granted access via dry contact.
Advise against extreme temperatures and electrostatic discharge risks from synthetic carpeting.
Prohibits installation near flammable or combustible gases/materials due to lack of intrinsic safety.
Avoid exposure of the biometric sensor to blinking lights, sunlight, or UV lights for optimal performance.
Emphasizes careful connection of Ethernet wires to avoid impacting signal sensibility.
Explains the support for the Clock & Data protocol on the Wiegand port and its wiring.
Provides a wiring diagram for Single Door Access Control using a push button.
A network connection is essential for initial terminal configuration, maintenance, and database management.
Details point-to-point Ethernet and LAN connections, covering static IP, DHCP, and tool usage.
Guidelines for setting static IP addresses and network masks when no DHCP server is present.
Instructions on configuring network parameters via MorphoBioToolBox and USB drive for terminal setup.
MorphoAccess SIGMA Lite Series terminals are fully compatible with MorphoManager application (version 8.0.3+).
Compatibility with MEMS (version 7.3.1+) and limitations in Morpho Legacy mode.
Compatibility with SecureAdmin (version v4.1.20.0.1+) and limitations in L1 Legacy mode.
Details the biometric sensor's region of interest and recommends specific fingers for optimal capture.
Provides solutions for common issues like dark or light fingerprint images and general capture advice.
Ensures correct finger height and alignment with the sensor for optimal capture.
Guides on maintaining the correct finger angle, parallel to the sensor, for accurate readings.
Details on avoiding bending or leaving the finger in the air for proper fingerprint capture.
Ensures the finger remains parallel to the sensor surface, avoiding rolling for accurate results.
Instructions on correctly positioning the RF card in front of the contactless card reader.
Details how users input their PIN code using the optional LCD touch screen keypad.
Manufacturer is not liable for issues arising from non-compliance with recommendations or incorrect terminal use.
Advise against self-repair and using unapproved accessories to maintain warranty and prevent damage.
Strongly recommends regular database backups for terminals operating in standalone mode.
Recommends regular synchronization for high time precision applications and notes typical clock deviation.
Specifies using a dry cloth for cleaning, especially the sensor, and prohibits acid, alcohol, or abrasive materials.
Provides physical mounting, electrical interfaces, and connection procedures for the terminal.
Covers terminal overview, configuration, functions, and detailed parameters for administration.
Details host system interface specifications and remote message formats for developers.
Documents new features, known issues, limitations, and recommendations for firmware updates.
Provides contact details for technical support and hotlines across various global regions.
Directs users to websites for the latest firmware, software, and document releases.
General| Brand | Safran |
|---|---|
| Model | morphoaccess sigma lite |
| Category | Touch terminals |
| Language | English |
