SAJ PDS23 Plus

Questions and Answers:

M
melendezelizabethAug 21, 2025
What to do if my SAJ PDS23 Plus Controller shows overload?
- C
  cantunathanAug 21, 2025
  If your SAJ Controller is showing an overload, it could be due to several reasons. It might be caused by acceleration that is too fast, in which case you should increase the acceleration time. Another cause could be restarting the motor too quickly after a trip-off; avoid doing this. Also, check the input power supply or wiring if the input voltage is too low. Finally, the load may be too heavy, requiring you to replace the controller with a higher-rated one.
T
Tracy ValenzuelaSep 3, 2025
What should I do if my SAJ PDS23 Plus Controller shows over-voltage during acceleration?
- L
  Lauren LyonsSep 3, 2025
  If your SAJ Controller displays an over-voltage error during acceleration, check the input power for any abnormalities. Also, avoid prompt restarts when a trip-off occurs.
J
Joseph CooleySep 1, 2025
What causes an IGBT module fault on a SAJ Controller?
- C
  Cynthia PrinceSep 1, 2025
  An IGBT module fault on your SAJ Controller can stem from several causes. The acceleration time might be too short; increase it. Interference from external equipment can also cause this issue; inspect and eliminate any interference. Also, check the grounding wire, as improper grounding can lead to this fault.
C
Carol HopkinsAug 30, 2025
How to troubleshoot over-voltage during deceleration with SAJ?
- T
  Traci RhodesAug 31, 2025
  To troubleshoot over-voltage during deceleration with your SAJ Controller, first, add proper braking units if the deceleration is too fast. Also, check the input power supply or wiring for any abnormalities in the input voltage.
J
James WallaceAug 29, 2025
What causes over-current during deceleration in an SAJ PDS23 Plus?
- M
  marydeanAug 29, 2025
  Over-current during deceleration in your SAJ Controller can be caused by deceleration that is too fast; increase the deceleration time to resolve this. If the load is too heavy and has large inertia, add proper braking units. The controller may also be under-rated, so consider replacing it with a higher-rated controller.
T
Timothy PayneAug 27, 2025
Why am I getting over-current at constant running speed on my SAJ Controller?
- K
  Kim SchultzAug 27, 2025
  If your SAJ Controller is showing over-current at a constant running speed, it could be due to a sudden change of load, so check the load. Another possibility is that the input voltage is too low, so check the input power supply or wiring. It could also be that the controller is under-rated, requiring a replacement with a higher-rated controller.
P
Philip DanielAug 26, 2025
What to do if there's over-current during acceleration with my SAJ PDS23 Plus Controller?
- S
  sharonmartinezAug 27, 2025
  If you're experiencing over-current during acceleration with your SAJ Controller, it could be due to a few reasons. The acceleration may be too fast, so try increasing the acceleration time. Also, check the input power supply or wiring, as the input voltage might be too low. If neither of these resolves the issue, the controller might be under-rated, and you should replace it with a higher-rated one.
H
Heather RushAug 25, 2025
How to fix an overheating SAJ PDS23 Plus?
- A
  Ana MarshallAug 25, 2025
  If your SAJ Controller is overheating, there are several things you can check. First, refer to the over-current remedy, as an instantaneous over-current could be the cause. Ensure there is no output short circuit by re-wiring the output. Check the cooling fans; replace them if they've stopped or are damaged, and clear any obstructions in the ventilation channel. If the ambient temperature is too high, try to decrease it. Inspect and tighten any loose cables or terminals. If these steps don't resolve the issue, it may be due to an abnormal power circuit.
D
destiny40Aug 23, 2025
Why is my SAJ PDS23 Plus showing a motor overload?
- S
  Sandra HernandezAug 23, 2025
  A motor overload on your SAJ Controller can occur if the input voltage is too low, so check the input power supply or wiring. Alternatively, the controller may be under-rated for the motor; in this case, consider replacing it with a higher-rated controller.