-50-
Electrical Adjustment
Grp / No. Item Function Range Initial Note
155 CCA
0 CCA Disable 0:Enable,1:Disable 0 - 1 0
160 VIDI
0 Brightness (Wheel)-Dynamic Brightness Wheel (Brightness) 0 - 10 4
1 Brightness (Wheel)-Not Dynamic Brightness Wheel (Color) 0 - 10 2
2 Color (Wheel)-Dynamic Brightness Wheel (Brightness) 0 - 10 5
3 Color (Wheel)-Not Dynamic Brightness Wheel (Color) 0 - 10 3
161 Lamp Sync
0 Brightness (Wheel)-x2 Mode 0 - 65535 178
1 Brightness (Wheel)-x3 Mode 0 - 65535 128
2 Color (Wheel)-x2 Mode 0 - 65535 429
3 Color (Wheel)-x3 Mode 0 - 65535 352
200 Option
0 Logo Display Prohibition 0:Menu 1:Forced 0 - 1 0
1 RS232C Baud rate 0: 19200bps 1: 9600bps 0 - 1 0
3 Shipping Set Shipping set when the value is set to 10 0 - 10 0
4 CABLE SW Long Cable 0: Disable 1: Enable 0 - 1 0
5 PW Debug Command Enable
0: Disable (Serial Command Enable)
1: Enable (PW Debug Mode)
0 - 1 0
6 Device Refresh Disable 0: Enable 1: Disable 0 - 1 0
11 HDCP EDID Data Setting 0: DVI EDID Data, 1: HDCP EDID Data 0 - 1 1
20 0 - 10 0
21 Lamp Warning Time (NORMAL) 1-16 4
22 Lamp Warning Time (ECO) 1-16 5
23 Lamp Warning Time (HIGH) 1-16 4
50 Lamp Replacement Display 1:On 0:Off 0 - 1 1
51 Filter Warning Display 1:On 0:Off 0 - 1 1
53 Filter Counter Reset Times Read only 0 - 255 0
54 Factory Default Executed Times Read only 0 - 255 0
56 Menu Position (X) X Offset 0 - 1024 0
57 Menu Position (Y) Y Offset 0 - 1024 0
58 Lamp Go Out Lamp goes out 0 - 1 0
59 LENS LOCK Warning Display 0: Enable 1: Disable 0 - 1 0
62 Color Wheel Warning 0: Enable 1: Disable 0 - 1 0
70 ADC Device Select for Analog PC 0 = ISL51002, 1 = PW392 AFE 0 - 1 0
71 ADC Device Select for Component 0 = ISL51002, 1 = PW392 AFE 0 - 1 0
80 Destination Language Set at Shipping 0:English 1:Japanese 0 - 1 0
100 Disable Auto Picture Control 0 : Normal operation 1 : Auto Picture Control Off 0-1 Initial: 1 Shipping 0
201 Option (Signal) Not Used
0 FrameLock Option Frame Lock Setting 1: Normal(PC) 0: OFF 0 - 1 1
1 Dither Enable 0: Disable 1: Enable 0 - 1 1
2 VSBEG 0 - 15 2
3 Field Sense Invert Enable 0: Disable 1: Enable 0 - 1 0
204 Simulation mode
0 PW392C Enable 0: Off, 1: On 0 - 1 0
1
205 Spread Spectrum
0 Enable 0 - 1 0
1 Spread Rate 0 - 300 100
2 Spread Frequency 0 - 500 150
210 Lamp Contorl
0 Dimmer SW 0:Auto 1:Manual 0 - 1 0
1 Manual Control
Lamp Power Manual Control (DIMMER_CTRL_LEVEL
0(Dark)~15(Bright))
0 - 15 0
2 DIMMER_CTRL_LEVEL1 Y Level1 Data for Dimmer 0 - 255 7
3 DIMMER_CTRL_LEVEL2 Y Level2 Data for Dimmer 0 - 255 14
4 DIMMER_CTRL_LEVEL3 Y Level3 Data for Dimmer 0 - 255 21
5 DIMMER_CTRL_LEVEL4 Y Level4 Data for Dimmer 0 - 255 28
6 DIMMER_CTRL_LEVEL5 Y Level5 Data for Dimmer 0 - 255 35
7 DIMMER_CTRL_LEVEL6 Y Level6 Data for Dimmer 0 - 255 42
8 DIMMER_CTRL_LEVEL7 Y Level7 Data for Dimmer 0 - 255 49
9 DIMMER_CTRL_LEVEL8 Y Level8 Data for Dimmer 0 - 255 56
10 DIMMER_CTRL_LEVEL9 Y Level9 Data for Dimmer 0 - 255 63
To Next Page
Loading...
