Sanyo PDG-DHT100L - Page 56

-56-
Electrical Adjustment
Grp / No. Item Function Range Initial Note
11 CR - GAIN AREA V START 0 - 1000 500
12 Image AREA H WIDTH YCBCR Level Acq. Width 0 - 4095 13
13 Image AREA V HEIGHT YCBCR Level Acq. Height 0 - 4095 9
14 Y - OFFSET TARGET 0 - 1023 4
15 CB OFFSET TARGET 0 - 1023 512
16 CR OFFSET TARGET 0 - 1023 512
17 Y - GAIN TARGET 0 - 1023 808
18 CB - GAIN TARGET 0 - 1023 892
19 CR - GAIN TARGET 0 - 1023 892
20 OFFSET Tolerance OFFSET Adj Tolerance 1 - 255 1
21 GAIN Tolerance GAIN Adj Tolerance 1 - 255 1
22 Image Level Tolerance Acq. Image Level Adj Tolerance 1 - 255 4
280 Auto PC Adjust
0 AutoPCAdjustEnable
Auto PC Operation with the un-supported signal in.
0: Enable 1: Disable
0 - 1 0
1 Frequency Step TotalDot Search Step 0-3 1
2 Frequency Threshold TotalDot Match 0 - 10 5
3 Fine Phase
Phase after Total Dot Adj.
0: Fine Phase Execute 1: Fine Phase Not Execute
0 - 1 1
4 BLKDET Black Level Detect Area 0 - 7 1
5 PHASEMSK
Phase Detect Filter
0: All Bits Enable, 1: Lower 1 bit Disable, 2: Lower 2 bit Disable, 3:
Lower 3 bits Disable
0 - 3 0
500 SCART(480i) [ON-Board (DVI-Dsub-HDMI)]
0 Total Dots 0 - 4095 858
1 Disp Dots 0 - 4095 674
2 H Back Porch 0 - 4095 138
3 V Back Porch 0 - 4095 42
4 Disp Line 0 - 4095 458
5 Clamp Position 0 - 4095 80
6 Clamp Width 0 - 4095 20
8 VSBEG 0 - 15 1
9 Filed Enable 0 - 1 1
10 FLDBEG 0 - 15 1
11 FLDEND 0 - 15 9
12 PHASE 0 - 63 16
22 (Sub) H Back Porch 0 - 4095 140
23 (Sub) V Back Porch 0 - 4095 42
25 (Sub) Clamp Position 0 - 4095 0
26 (Sub) Clamp Width 0 - 4095 0
28 (Sub) VSBEG 0 - 15 1
29 (Sub) Filed Enable 0 - 1 0
30 (Sub) FLDBEG 0 - 15 4
31 (Sub) FLDEND 0 - 15 10
32 (Sub) PHASE 0 - 63 16
501 SCART (575i) [ON-Board (DVI-Dsub-HDMI)]
0 Total Dots 0 - 4095 868
1 Disp Dots 0 - 4095 670
2 H Back Porch 0 - 4095 152
3 V Back Porch 0 - 4095 62
4 Disp Line 0 - 4095 534
5 Clamp Position 0 - 4095 90
6 Clamp Width 0 - 4095 20
8 VSBEG 0 - 15 1
9 Filed Enable 0 - 1 1
10 FLDBEG 0 - 15 1
11 FLDEND 0 - 15 9
12 PHASE 0 - 63 16
22 (Sub) H Back Porch 0 - 4095 156
23 (Sub) V Back Porch 0 - 4095 62
25 (Sub) Clamp Position 0 - 4095 0
26 (Sub) Clamp Width 0 - 4095 0