MODULES AND FUNCTIONS
Bubbleland
Symbol Module Range Default
MISCELLANEOUS MODULES
Cont.
LOGGING MODULE
x 3
The Lo
in
module will lo
50 analo
ue values and 50 di
ital states.
Each value/state lo
will be taken when a second di
ital input is
momentaril
set to ON. A di
ital output is switched ON when the
lo
in
module is full. This output can be used to disable the lo
in
module.
If the lo
in
module is not disabled it will continue to lo
and overwrite
the oldest lo
ed information.
Lo
ed data can be viewed via the IAC 600 Touch-screen.
SYSTEM MODULE
x 1
This module ma
be placed on screen as often as re
uired
This module has no inputs or outputs and is intended to
ive
information on s
stem settin
s and allow them to be chan
ed. This
module would normall
onl
be used when commissionin
Preset Application
0 = Software Preset
This displa
s the current preset application number and allows a new
one to be loaded.
0 to 4 –
Detector Speed
This allows the detector sensin
speed to be set. The Fast speed
should onl
be set when usin
simulators for the detector inputs.
NOTE:-
This must be set to Normal for normal controller operation. Fast or Normal Normal
Force Reset
This button is used to force the controller to reset.
Yes or No No
Reload Defaults
This button is used to force the controller to reload all of its default
values.
NOTE:-
This will overwrite an
parameters set b
the user ori
inall
.
The controller is also automaticall
reset.
Yes or No No
Null Outputs
This button is used to send the controller into its Null Output mode. In
this mode all controller outputs are turned off and all module links are
disconnected. On leavin
this mode the module links are re-connected
and the outputs resume normal operation. Null Output is the hi
hest
priorit
override on the controller.
Yes or No No
If the IAC keeps sendin
itself into Null Output Mode, reload defaults
should be used to clear it. This will overwrite an
parameters set b
the user.
Detector Sequence
This settin
selects the se
uence in which the detectors are read. The
default settin
is 0 and this settin
ives an e
ual priorit
to all
detectors. Selectin
1 will
ive priorit
to temperature
resistive
input
1 and 2
ives priorit
to analo
ue
Volta
e
input 1. Se
uences 1 or 2
should be used when a fast reactin
loop must be controlled.
0 to 2 0
REFERENCE MODULES
DIGITAL MONITOR MODULE
x 8
This module displa
s the state of an
di
ital output connected to it.
This would
enerall
be used for checkin
module operation.
Current State
review onl
This parameter displa
s the current input state of the module.
On or Off –
DIGITAL REFERENCE MODULE
x 8
This module
ives a sin
le di
ital output that can be turned on or off b
clickin
on the module. This would
enerall
be used for checkin
module operation.
Current State
This parameter allows the user to chan
e the output of the module.
On or Off Off
ANALOGUE MONITOR MODULE
x 12
This module displa
s the current analo
ue value of an
analo
ue
output connected to it. The value can be scaled in the same wa
as
with scalin
modules however there is no ph
sical output
ust a value.
This would
enerall
be used for checkin
module operation or
presentin
a scaled value.
For instance to displa
temperatures to 1 decimal place, set the input
minimum to
−
40, the output minimum to
−
400, the input maximum to
150 and the output maximum to 1500. The
Value/10
parameter will
now displa
temperature to 1 decimal place.
Value
review onl
This parameter displa
s the analo
ue input value AFTER the scalin
has been calculated.
–32,000 to 32,000 –
Value/10
This parameter displa
s the analo
ue input value AFTER the scalin
has been carried out. this value is divided b
10.
–32,000 to 32,000 0
Input Minimum Value
–10,000 to 10,000 0
Output Minimum Value
–32,000 to 32,000 0
Input Maximum Value
–10,000 to 10,000 100
Output Maximum Value
–32,000 to 32,000 100
DS 2.951A 12 - 24 05/98
To Next Page