SawStop 10” Industrial Cabinet Saw 67
Overall saw dimensions: 44” w x 34” d x 34” h
69 1/4”w x 36 1/2” d x 34” h (w/ optional fence & 36” rails)
85 1/4” w x 36 1/2” d x 34” h (w/ optional fence & 52” rails)
Cabinet footprint: 20” w x 25” d
Cast iron table: 24” w x 30” d, 44” w x 30” d (w/ extension wings)
Extension wing: 10” w x 30” d
Extension table (optional): 24” w x 30” d (36” rails), 40” w x 30” d (52” rails)
Weights (may vary with motor): 530 lbs (table saw only)
635 lbs (w/ optional fence, 36” rails & table)
685 lbs (w/ optional fence, 52” rails & table)
Shipping weight (approx.): 675 lbs (table saw only)
Blade: 60-tooth, professional grade, 5/8” arbor
Blade diameter: 10”
Blade tilt: Left
Blade kerf: 3 mm
Blade plate thickness: 2 mm
Max. depth of cut, blade at 0º: 3 1/8”
Max. depth of cut, blade at 45º: 2 1/4”
Max. rip, right of blade: 52 1/2” (w/ optional 52” rails)
36 1/2” (w/ optional 36” rails)
Max. rip, left of blade: 12 1/2”
Dado diameter: 8” (requires a separate brake cartridge)
Dado max. width: 13/16”
Arbor diameter at blade: 5/8”
Main bearing size: 62 mm OD x 30 mm ID
Second bearing size: 52 mm OD x 25 mm ID
Table in front of blade (max. elevation): 11”
Table behind blade (max. elevation): 9 3/4”
Arbor Runout: 0.001” Maximum Allowable Runout
Blade Lateral Movement Over Full Elevation Range: 0.006” Maximum
Table Flatness Measured Diagonally: 0.010” Maximum Gap
Overall Table and Extension Wing Flatness: 0.025” Maximum Gap
Blade Alignment with Miter Slot: 0.010” Maximum displacement
Deviation of Miter Gauge Indexing Stops
from actual angle: ±0.25º
Alignment between Spreader and Blade: 0.010” Maximum difference
Miter slots: T-shaped, 3/4” at top, 1” at bottom, 3/8” deep
Dust collection port diameter: 4”
Riving knife / spreader thickness: 2 mm
Blade guard: polycarbonate, extends only 5/8” to right of blade
Standard Insert: zero clearance, phenolic core, melamine surfaces
Dado Insert: zero-clearance, phenolic core, melamine surfaces
Belts: 2 V-ribbed belts— arbor belt is static dissipative
Hand Wheels: 8” diameter, cast iron with chrome handle
Motor Options:
3 hp, 1 phase, 230V, 13A, 60 Hz, TEFC 5 hp, 3 phase, 600V, (Canada)
5 hp, 1 phase, 230V, 20.5A, 60 Hz, TEFC 7.5 hp, 3 phase, 600V (Canada)
5 hp, 3 phase, 230V, 13A, 60 Hz, TEFC 3 hp, 1 phase, 240V, 50 Hz (Australia)
5 hp, 3 phase, 480V, 7A, 60 Hz, TEFC 5 hp, 3 phase, 415V, 50 Hz (Australia)
7.5 hp, 3 phase, 230V, 19A, 60 Hz, TEFC
7.5 hp, 3 phase, 480V, 9A, 60 Hz, TEFC 3 hp, 3 phase, 230V, 8A, 60 Hz, TEFC (discontinued)
Cabinet Saw Specications
To Next Page