Scanjet SC 45TW - Page 20

#SC 45TW-SS 10 – 110202Page 20 of 40
cover
8. Withdraw cover, bearing ring (pos. 8), gear and nozzle housing
8
Designer
Date
Date
Drawer
Surface treatment
Weight
Note
Dimension
Material
General Tolerances
Tolerance ISO 2768-m
Gen. surface
N9
This document is our property and shall not without our permission in writing be altered, copied, used for manu- facturing or communicated to any person or company.
Drawing no. / Ritningsnr.
Format
SC45TW Nytt utf Ø9-12 mm
A4
Scale
SC45TW-S-XX
1:2.6
SC45TW New Ø9-12 mm
Denna handling är vår egendom och får ej utan vårt skriftliga medgivande ändras, kopieras, användas för tillverkning eller delges annan person eller firma.
SS-ISO 2768-m for machined parts (30)-120=
0.3
0.5-3=
0.1 (120)-315=
0.5
(3)-30=
0.2 315)-1000=
0.8
P01
Törnedalsgatan 1, 275 21 Sjöbo
SWEDEN
JC
Revision
05-03-24
E
No.
Revision note
Date
Sign.
Qty.
Ins.
gram
12
Designer
Date
Date
Drawer
Surface treatment
Weight
Note
Dimension
Material
General Tolerances
Tolerance ISO 2768-m
Gen. surface
N9
This document is our property and shall not without our permission in writing be altered, copied, used for manu- facturing or communicated to any person or company.
Drawing no. / Ritningsnr.
Format
SC45TW Nytt utf Ø9-12 mm
A4
Scale
SC45TW-S-XX
1:2
SC45TW New Ø9-12 mm
Denna handling är vår egendom och får ej utan vårt skriftliga medgivande ändras, kopieras, användas för tillverkning eller delges annan person eller firma.
SS-ISO 2768-m for machined parts (30)-120=
0.3
0.5-3=
0.1 (120)-315=
0.5
(3)-30=
0.2 315)-1000=
0.8
P01
Törnedalsgatan 1, 275 21 Sjöbo
SWEDEN
JC
Revision
05-03-24
E
No.
Revision note
Date
Sign.
Qty.
Ins.
gram
9. Note the two O-rings (pos. 12) inside the nozzle
housing
25
Designer
Date
Date
Drawer
Surface treatment
Weight
Note
Dimension
Material
General Tolerances
Tolerance ISO 2768-m
Gen. surface
N9
This document is our property and shall not without our permission in writing be altered, copied, used for manu- facturing or communicated to any person or company.
Drawing no. / Ritningsnr.
Format
SC45TW Nytt utf Ø9-12 mm
A4
Scale
SC45TW-S-XX
1:2
SC45TW New Ø9-12 mm
Denna handling är vår egendom och får ej utan vårt skriftliga medgivande ändras, kopieras, användas för tillverkning eller delges annan person eller firma.
SS-ISO 2768-m for machined parts (30)-120=
0.3
0.5-3=
0.1 (120)-315=
0.5
(3)-30=
0.2 315)-1000=
0.8
P01
Törnedalsgatan 1, 275 21 Sjöbo
SWEDEN
JC
Revision
05-03-24
E
No.
Revision note
Date
Sign.
Qty.
Ins.
gram
10. Turn the machine upside down
11. Undo the bolts (pos. 25) in the bottom plate to
remove the gearbox
12. Pull out the turbine shaft