23GB
11. Cleaning and maintenance
Important.
Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time us-
ing a cloth. In order to extend the service life of the tool, oil
the rotary parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive prod - uct.
General maintenance
After using your belt/disc sander, clean it completely
and lubricate all sliding and moving parts. Apply a
light coat of automotive type paste wax to the workta-
ble to help keep the surfaces clean.
Cleaning
Dust can collect in the belt and disc grinder. Check
regularly (preferably after every use) and remove
dust, e. g. by blowing away or carefully with com-
pressed air.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the follow-
ing parts are therefore also required for use as con-
sumables.
Wear parts*: Carbon brushes, v-belt, grinding me-
dium
* Not necessarily included in the scope of delivery!
12. Storage
Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C.
Cover the electrical tool in order to protect it from
dust and moisture.
Store the operating manual with the electrical tool.
13. Electrical Connection
The installed electric motor is connected and is ready
to work.
The connection complies with the relevant VDE and
DIN regulations.
The customer-side mains supply and the used exten-
sion line must meet these regulations.
Defective Electric Connection Lines
Often, insulation damages occur on electrical con-
nection lines.
Causes are:
• Drag marks if connection lines are led through win-
dow or door clearances.
• Kinks due to improper attachment or routing of the
connection line.
• Cuts caused by running over the connection line.
• Insulation damages caused by pulling the connec-
tion line out of the wall socket.
• Fissures caused by the ageing of the insulation.
Such defective electric connection lines must not be
used and are hazardous due to the insulation dam-
ages.
Regularly check the electrical connection lines for
damages. Please make sure that the connection
lines are disconnected from the mains supply during
the check.
Electrical connection lines must comply with the rel-
evant VDE and DIN regulations. Only use connection
lines labelled with H05VV-F. The labelling of the con-
nection cable with the type specication is required.
AC motor
• The mains voltage must be 220 - 240 V~
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm
2
.
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Machine data - type plate
14. Disposal and recycling
The equipment is supplied in packaging to preven it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective
components must be disposed of as special waste.
Ask your dealer or your local council.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must
not be disposed of together with domestic
waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical and
electronic equipment (WEEE).
This product must be disposed of at a designated col-
lection point. This can occur, for example, by handing
it in at an authorised collecting point for the recycling
of waste electrical and electronic equipment. Im-
proper handling of waste equipment may have nega-
tive consequences for the environment and human
health due to potentially hazardous substances that
are often contained in electrical and electronic equip-
ment. By properly disposing of this product, you
are also contributing to the effective use of natural
resources. You can obtain information on collection
points for waste equipment from your municipal ad-
ministration, public waste disposal authority, an au-
thorised body for the disposal of waste electrical and
electronic equipment or your waste disposal com-
pany.
To Next Page
Loading...
Need help?
General
