Why is chip ejection obstructed on my Scheppach Lathe even with a dust extractor?
If chip ejection is obstructed during surface planing and thicknessing on your Scheppach Lathe, even with a dust extractor, the suction performance may be too weak. Use a dust extractor unit having an airflow rate at the suction connection of at least 20 m/s.
What to do if the workpiece jams during thicknessing on my Scheppach Lathe?
If the workpiece jams during thicknessing on your Scheppach Lathe, the cutting depth may be too great. Reduce the cutting depth and machine the workpiece in several passes.
Why is the machined surface cracking on my Scheppach Lathe?
Cracking on the machined surface of your Scheppach Lathe workpiece can occur because: * The workpiece was machined against the grain; machine it from the opposite direction. * Too much material was planed in one pass; machine the workpiece in several passes.
What causes obstructed chip ejection during thicknessing on a Scheppach Lathe?
If you experience obstructed chip ejection during thicknessing on your Scheppach Lathe (without a dust extractor), consider these points: * Too much chip removal; reduce it. * Blunt knives; replace them. * The wood may be too humid; dry the workpiece.
Why is the speed decreasing when planing with my Scheppach Lathe?
If the speed decreases when planing with your Scheppach Lathe, it could be due to: * Removing too much material; reduce the chip removal. * Blunt knives; replace them.
What to do if my Scheppach PLM1800 cannot be switched on?
If the Scheppach Planer machine cannot be switched on, you should first check the power supply. If the power supply is fine, the carbon brush might be worn and you should take the machine to your service point.
How to improve the surface finish on a Scheppach Lathe?
An unsatisfactory surface finish on your Scheppach Lathe can be due to several factors: * The planing blade might be blunt or worn, in which case you should replace or sharpen it. * The planing blade might be filled with chips; remove them. * Uneven feed can also cause this, so feed the workpiece with constant pressure and at a reduced speed.
How to troubleshoot a Scheppach Lathe that won't turn on?
If your Scheppach Lathe won't switch on, there are a couple of things to check: * First, ensure that the power supply is working correctly. * Second, the carbon brush might be worn. If this is the case, take the machine to your service point.
Why is chip ejection obstructed (with dust extractor) with surface planing and thicknessing using my Scheppach Planer?
If chip ejection is obstructed (with a dust extractor) during surface planing and thicknessing with your Scheppach Planer, the suction performance may be too weak. Use a dust extractor unit having an airflow rate at the suction connection of at least 20 m/s.
Why is chip ejection obstructed (without dust extractor) when thicknessing with my Scheppach PLM1800 Planer?
If chip ejection is obstructed (without a dust extractor) when thicknessing with your Scheppach Planer, it could be due to too much chip removal, so reduce it. Another reason could be blunt knives, which should be replaced. Also, the wood may be too humid, so dry the workpiece.
Key safety guidelines for using the equipment safely.
Essential practices for operating the machine without risk.
Procedure for setting the planing depth using the crank.
Step-by-step guide on how to use the thickness planer.
General| Type | Paring chisel |
|---|---|
| Power | 1500 W |
| Material | Plastic, Steel |
| Feed rate | 7.4 m/min |
| Idle speed | 8500 RPM |
| Handle color | Black, Blue |
| Handle material | Metal, Plastic |
| AC input voltage | 230 V |
| Number of blades | 2 |
| AC input frequency | 50 Hz |
| Surface planing material removal (max) | 152 mm |
| Thickness planing material removal (max) | 330 mm |
Weight and Dimensions| Depth | 630 mm |
|---|---|
| Width | 589 mm |
| Height | 500 mm |
| Thicknessing table dimensions (W x D) | 330 x 630 mm |
To Next Page
