Sencore SMD 989 - Page 9

SMD 989– User Manual
Page 9 (105)
Table of Figures
Figure 1: Basic SMD 989 platform .......................................................................................................... 13
Figure 2: Contact closure alarm output connector ............................................................................... 13
Figure 3: Contact closure pin connection ............................................................................................. 14
Figure 4: SMD 910 single TS input with IF output ................................................................................. 15
Figure 5: SMD 912(A) single TS input with monitor and IF output ...................................................... 15
Figure 6: SMD 920 L-Band output - shown with SMD 910 .................................................................... 16
Figure 7: SMD 920 L-Band output - shown with SMD 912(A) ............................................................... 16
Figure 8: SMD 940..................................................................................................................................... 17
Figure 9: SMD 942 and SMD 944 ............................................................................................................. 17
Figure 10: SMD 952 Dual Redundant AC Power Supply ...................................................................... 18
Figure 11: SMD 954 Dual Redundant DC Power Supply ...................................................................... 18
Figure 12: SMD 963 option multistream TS input with IF output ......................................................... 19
Figure 13: Rack mounting ....................................................................................................................... 22
Figure 14: Logon screen .......................................................................................................................... 23
Figure 15: Bay 1 home screen ................................................................................................................. 23
Figure 16: Single ASI input ...................................................................................................................... 24
Figure 17 Input LIst - Shows Disabled inputs with Multistream License............................................ 24
Figure 18: ASI configuration ................................................................................................................... 25
Figure 19 Inputs on SMD 910 Modulator ................................................................................................ 26
Figure 20: Expanded IP status ................................................................................................................ 27
Figure 21 Configure IP Receive Menu .................................................................................................... 27
Figure 22 IP inputs on SMD912 ............................................................................................................... 29
Figure 23 IP Input Settings on SMD 912(A) modulator ......................................................................... 30
Figure 24 IP Input Details List with SMD 912(A) .................................................................................... 32
Figure 25 Single stream status ............................................................................................................... 33
Figure 26 Multistream status ................................................................................................................... 33
Figure 27 Configuration Modulator settings menu example ............................................................... 34
Figure 28 Modulation Mode selection - SMD910 (Left) and SMD912 (Right) ...................................... 34
Figure 29 Primary & backup input selection, failover selections ........................................................ 35
Figure 30: Single stream DVB-S2 Configuration shown ...................................................................... 36
Figure 31: Supported modulations & code rates for DVB-S/DSNG and DVB-S2 ............................... 37
Figure 32: Carrier ID – Global Unique ID ................................................................................................ 39
Figure 33: Carrier ID Configuration ........................................................................................................ 39
Figure 34 Configure TS Analysis ............................................................................................................ 41
Figure 35 SMD 963 multi-stream configuration ..................................................................................... 42
Figure 36: PRBS Pseudo Random Binary Sequence ............................................................................ 43
Figure 37 BISS Scrambling configuration ............................................................................................. 44
Figure 38 TurboPSK (Single) modulation selection.............................................................................. 45
Figure 39 Advanced Modulation Turbo PSK modes and code rates .................................................. 46
Figure 40: Reduced Latency Selections ................................................................................................ 47
Figure 41: Configure DVB-SX2 Modulation/FEC ................................................................................... 48
Figure 42: Modulation/FEC code rates DVB-SX2 .................................................................................. 49
Figure 43: Outputs section ...................................................................................................................... 52
Figure 44: IF settings ............................................................................................................................... 53
Figure 45: RF settings .............................................................................................................................. 54
Figure 46: RF settings with 10MHz option ............................................................................................. 54
Figure 47: Admin tab ................................................................................................................................ 55
Figure 48: Password/Unit update location ............................................................................................. 55
Figure 49: Profile Manager ...................................................................................................................... 56
Figure 50: Setting password ................................................................................................................... 56
Figure 51: MIBs ......................................................................................................................................... 57
Figure 52: Updating software .................................................................................................................. 57
Figure 53: Uploading file .......................................................................................................................... 57
Figure 54: Upload successful .................................................................................................................. 58