To Next PageTo Next PageHow to fix abnormal vibrations in Seppi Farm Equipment?
If you observe abnormal vibrations in your Seppi Farm Equipment, it could be due to several reasons. One potential cause is an unbalancing of the tool support rotor, in which case you should re-balance the rotor. Alternatively, a counterweight or one or more tools might be broken. If this is the case, replace the tools.
Why is the cutting/mulching quality low on my Seppi Farm Equipment?
If you experience low-quality cutting or mulching with your Seppi Farm Equipment, several factors could be responsible. The rotor might not be reaching the intended speed, in which case you should check the belt tension. Also, the machine adjustment might not be compliant with instructions, so verify the PTO rpm. If your forward speed is too high, adjust the hood or roller and reduce forward speed. Finally, check if the tools are worn and replace them if necessary.
What to do if the PTO turns but the rotor stays still on Seppi Farm Equipment?
If the PTO turns but the rotor stays still on your Seppi Farm Equipment, it could be due to a broken gearbox, broken belts, or a burnt clutch. To resolve this, replace or repair the gearbox, replace the belts, or replace the clutch, as appropriate.
Why does my Seppi Farm Equipment have excessive power absorption?
If your Seppi Farm Equipment experiences excessive power absorption, it could be due to the hood or roller not being adjusted properly. In this case, adjust the machine according to the instructions. Alternatively, there might be too much material and too little tractor power, so find a compromise between power and forward speed.
What to do if the tools break on Seppi Farm Equipment?
If the tools break, or the bars are cut on your Seppi Farm Equipment, it may be due to the presence of stones. Remove this type of material to avoid issues. The rotor speed may also be too low or too high; increase or lower the nominal speed accordingly. Insufficient power could also be a factor, so reduce the workload.
Why is the rotor blocked on my Seppi Farm Equipment?
If the rotor is blocked on your Seppi Farm Equipment, it could be due to a foreign body stuck, in which case you should turn the rotor in the opposite direction using suitable tools. It may also be caused by missing lubrication, so lubricate the equipment. Alternatively, the gears or bearings in the gearbox could be broken, requiring you to replace them. Finally, worn or broken rotor bearings could be the cause, so replace the bearings and gaskets.
Why are the bearings frequently breaking on my Seppi Farm Equipment?
Frequent breakage of bearings in Seppi Farm Equipment can be attributed to several causes. A bent frame, resulting in excessive axial loads, can be a factor; in this case, repair the frame. Missing lubrication is another potential cause, so ensure proper lubrication. Broken sealing systems can also lead to this issue, so replace sealing rings, etc.
Why do the belts wear quickly on my Seppi Farm Equipment?
Premature wear of belts or disk clutches in Seppi Farm Equipment can occur due to several reasons. A low PTO rotation speed may be the cause, so adjust the rotation speed as foreseen in the user manual. Starting the machine above the material to be mulched can also lead to this issue, so bring the machine to the proper speed before cutting. If the rotor cannot start and the belts slip, check whether the rotor is blocked. Insufficient belt tension can also cause premature wear, so tension the belts according to the instructions.
What causes broken labyrinths and sealing rings in Seppi Farm Equipment?
If labyrinths and sealing rings are broken in your Seppi Farm Equipment, it could be due to excessive lubrication, fatigue, or missing lubrication. In any of these cases, replace the sealing rings and lubricate correctly.
Requirements for machine operators.
Details safety rules and identifies residual risks.
Defines the machine's intended purpose and applications.
Lists and describes safety devices on the machine.
Steps for attaching the machine to the tractor, including PTO and hydraulic systems.
Steps for machine start-up and operational processing.
How to check and adjust belt tension.
Instructions for lubricating machine components.
Checking safety devices and labels.
Procedures for replacing machine tools.
Procedures for replacing fixed knives.
Guide to diagnosing and resolving machine malfunctions.
General| Max Working Depth | 250 mm |
|---|---|
| Rotor Speed | 1000 rpm |
| Max. diameter of trees | 300 mm |
| Working Width | 2500 mm |
| Rotor Diameter | 600 mm |
