Sharp AR-M276

AR-M236/M276/M237/M277 SIMULATION 8 - 7
Note: Executable only when the SPF/RSPF is installed.
Operation/procedure
Used to display the operations of sensors and detectors in the finisher
section.
The active sensors and detectors are highlighted.
Note: Executable only when the finisher is installed.
Operation/procedure
Select the load to be checked with the 10-key, and press the [START]
key.
The finisher main motor operates for 10sec, the staple motor 5 times,
the tray lift-up motor one reciprocating operation, other motors max. 20
reciprocating operations from the home position, the solenoid repeats
500msec ON and 500msec OFF 20 times.
The staple operation motor operates only when there is no cartridge
installed.
Note: Executable only when the finisher is installed.
Operation/procedure
After the paper size is set, the side guide plate and the rear guide plate
are set.
1. Enter the desired item with the 10-key, and press the [START] key.
2. Enter the adjustment value with the 10-key, and press the [START]
key.
There are 6 adjustment values for the side guide plate, and 12 for the
rear guide plate. The adjustment position is determined from the table
below according to the paper size.
Item Content
1 DTM-F SPF/RSPF motor forward rotation
2 DTM-R SPF/RSPF motor reverse rotation
3 DFCL SPF/RSPF paper feed clutch
4 CLH SPF/RSPF PS clutch
5 GSOL Document exit gate solenoid
6 RSOL Document exit pressure solenoid
3
3-2
Purpose Operation test/check
Function
(Purpose)
Used to check the operation of sensor and detector in
the finisher and the related circuit.
Section Finisher
Item Operation
INPD Finisher paper entry sensor
FWPS Paper width sensor
JGHP1 Side guide plate HP sensor
JGHP2 Rear edge plate HP sensor
JGPD Tray paper empty sensor
T1OD 1st tray exit sensor
T1PF 1st tray paper full sensor
PGOP JAM processing PG open/close detection sensor
T2OD 2nd tray exit sensor
OFHP Offset HP sensor
T2UP Tray position sensor (upper)
T2DN Tray position sensor (lower)
JGDSW Tray jam processing interlock
EVRE Lift-up drive control sensor
STHP Staple HP sensor
READY Self priming sensor
LSTS Staple empty sensor
NCTS Cartridge empty sensor
STND Staple supply cover open/close sensor
T2PUD 2nd tray upper surface sensor
3-3
Purpose Operation test/check
Function
(Purpose)
Used to check the operation of the load in the finisher
and the control circuit.
Section Finisher
Item Operation
Item Content
1 JGM1 Side guide plate drive motor
2 JGM2 Rear edge plate drive motor
3 FM-600 Finisher main motor (600dpi)
4 FM-1200 Finisher main motor (1200dpi)
5 EVM Tray lift-up motor
6 OFM Tray offset motor
7 STM Staple operation motor
8 OGSLR Transport selection gate solenoid (R)
9 OGSLL Transport selection gate solenoid (L)
10 JGSL1 Rear edge plate drive solenoid
11 JGSL2 Upper alignment plate drive solenoid
12 SHTSL Shutter drive solenoid
13 T2SCL Paper exit roller clutch
14 STGSL Paper holding solenoid
3-6
Purpose Adjustment
Function
(Purpose)
Used to adjust the alignment position (side regulation
plate, rear edge regulation plate) for each paper size.
Shifts to the specified paper size position.
Section Finisher
Item Operation
Item Content
Setting
range
Default
1 PAPER SIZE Paper size
(1:A3, 2:A4, 3:B4, 4:B5,
5:A4R, 6:WLT, 7:LT,
8:LG, 9:FC, 10:LTR,
11:8K, 12:16K)
1-12 A4
2 JOGGER POS X Side guide plate 1-99 50
3 JOGGER POS Y Rear edge guide plate
Paper size
Side guide plate
adjustment value number
Adjustment value number
of the rear edge guide
plate
A3 1 2
A4 1 9
B4 3 3
B5 3 10