AR-M236/M276/M237/M277 SIMULATION 8 - 17
Operation/procedure
The trouble error codes are displayed in the sequence of the latest one
first. Max. 40 items of information are stored. (Older ones are deleted
in sequence.) The machine condition can be estimated by this data.
Operation/procedure
Used to display the ROM version of each section.
[Display example]
ROM version 1.250
→ [1.25] (up to 2 decimal places)
The display of the protocol monitor and the soft SW follows this dis-
play.
If it is not installed, "- - - - - - - - - -" is displayed.
[Label code display]
Contents of "XXX" section on the display below
*1: Display at the current state
Operation/Procedure
(Initial screen)
The currently set value is highlighted beside the adjustment item.
1. Select the adjustment item with the 10-key.
2. Press the [START] key.
The display is shifted to the copy menu and the set value is stored.
3. Select the paper feed tray and the print density.
4. Press the [START] key.
Copying is started. (Printing at 1200dpi cannot be made.)
After canceling a jam (After picking up, the [C] key is invalid.)
When the other information is repeatedly printed, the display may show
the message, "Remove original from original table." However, the
operation is performed normally.
* When the IMC board is not installed, key input is disabled.
* Duplex print cannot be made.
* For the FAX SIM setting list, the display and the operating proce-
dures differ.
22-4
Purpose Adjustment/setting/operation data output/check
(display/print)
Function
(Purpose)
Used to check the total trouble (self diag) history.
Item Trouble
22-5
Purpose Adjustment/Setting/Check
Function
(Purpose)
Used to check the ROM version of each unit (section).
Item Software
S/N Machine serial number
MCU Main Control Unit
IMC IMC
OPE Panel + Panel label code
PRINTER
PRINTER
NIC
NIC (For the Soft Nic, the Soft Nic version is displayed.
When the AR-NC5 is installed, the AR-NC5J version is
displayed.)
FINISHER
FINISHER
FAX
FAX
Panel
display
Destination Selection code
Panel software support
language
JPN Japan Japanese, American
English, English
EFS SEC AJ/AM American English, English,
French, Spanish
SECL AL/AC
SUK BK/BB
EEU SEEG/
SEA/East
Europe,
etc.
GG/GD English, German, Polish,
Czech, Hungarian, Greek,
Turkish, Russian, French,
Italian, Slovak
NEU SEF/
SEES/
SEIS/SEN,
etc.
BG/DG/
BD/DD
English, German, French,
Spanish, Dutch, Italian,
Portuguese, Swedish,
Norwegian, Finnish,
Danish
SCA/SCNZ BA/BN American English, English,
French, Spanish
Distributor
area
CHN SOCC BZ UE5 Simplified Chinese,
American English, English
TWN Taiwan BE/BT UT1 Traditional Chinese (Local
support), American
English, English
EFS *1 Special
countries
American English, English,
French, Spanish, Hebrew
(Local support)
22-6
Purpose Adjustment/setting/operation data output/check
(display/print)
Function
(Purpose)
Used to print each key operator setting, the account
information, and the machine adjustment values.
Item Data Setting/adjustment data
Item Content
1 ALL All lists group print
2 KEY OPE Key operator information list
3 ALL COUNTERS List of total number of prints
4 AUDITOR NO. Department number list
5 MACHINE SIM
SETTING
Machine simulation setting list
6 FAX SIM SETTING*1 FAX simulation setting list (Only when
the FAX board is installed. The display
does not go to the print data transfer
display, but to the FAX SIM menu.)
Panel
display
Destination Selection code
Panel software support
language
Panel label code
To Next Page
Loading...
